Mount-It! Full Motion TV Mount: Heavy-Duty Swivel for 32-60 inch Screens, 4K Flat Panel, VESA Up To 750x450 Review

Simply amazed at how excellent the materials and durability are at this price point! I didn't want to buy a $20 mount and risk falling into a $700 TV, but I didn't want to pay 20% of what I paid for my TV for the mount either! I'm so glad I stumbled across this mountain! Great price for quality material. It comes mostly assembled (excluding screws and TV brackets). You will need a bolt finder and a drill/screwdriver. My brother hung the bracket himself and attached the TV. It came out…

Easy to install and weighs a ton so you can feel the weight of the mount and know it's strong enough to support huge plasma TVs like the one I've hung with this mount have to hold. I would also like to add that my plasma is about 10 years old and the heaviest plasma. So if you have a new 40" or larger, this mount will impress! It has a built in spirit level so all you have to do is stick it into the wall after finding the studs with the stud finder and line them up, mark the spots where you…

I bought this mount for my Panasonic 55" ST60. It is well built, offers flexible mounting options and hardware and does exactly what it was designed to do. My only reasons For that he didn't give it 5 stars, it's because of the quality of the instructions, I had to do some research online to figure out where to attach the Panasonic. Also a little tugging and jerking when adjusting the tilt. I guess I do added a few nylon/teflon washers would have smoothed out the action but didn't get a chance…

I used this mount on my Panasonic 50" plasma. I did all the work myself but it would have been better to have a second person help hold things up. If your House has 16" wall studs. You can go in the middle. Just remember that the center point between the two stands you choose is the center point of your TV on the wall. If your house is in the center 24" stand has, as is usual with 2x6 construction, you must anchor the lumber horizontally to the wall and then attach the brace to that lumber. The

This is a heavy duty mount and although it says it's designed for TVs up to 60", it works great for my 65VT50. As another reviewer mentioned, the screws on the back of the TV weren't long enough or other screws were too long. So I went to a hardware store and bought longer screws and bought new bolts as someone said they shear off. I used my own level but it matched the level on the mountain. Using a screwdriver, I hung the bracket myself and lifted the TV onto the bracket myself. (Where are…

I needed a wall mount for my 32" Panasonic Viera that swivels in all directions and still remains stable. I received it yesterday and thought it was heavy and heavy to bear due to its own weight I marked the studs, drilled 4 holes, took a 4-screw DeWalt screwdriver, slung it over my shoulder and screwed the screws in. Next four screws on the back of the TV, immediately to the Hooks hung, set screws adjusted and I can tilt, rotate, extend, slide back the TV as easily as possible. I say it can…

I used this to install a Panasonic 50 inch plasma (TC-P50S2) in November 2010. The mount arrived very quickly (to California) and was not damaged. I had a bit of an issue with the length of the screws, assuming the brackets are attached to the back of the TV. When I called Panasonic to verify the length of the screws used, they recommended 15mm, which was not included. After checking the depth of the holes on the back of the TV, I found that 20mm would be enough to hold the TV without being…

I bought this wall mount for a Panasonic 50 inch plasma. As described, it is VERY strong and heavy. Overall impression and workmanship are good. I didn't find any jagged edges or other cracked areas. The levers are a bit stiff to operate, which is good because you don't want the TV to move in the wind. It would be nice to have a helping hand laying out the wall, since the whole unit is heavy. As for the cons: 1. The first obvious problem is the distance between the wall plate mounting holes…

I have a 42 inch Panasonic plasma TV. It doesn't have standard hole spacing on the back (measure yours first). This mount is designed like a tank and can easily hold my TV. No, don't give up, it's hard. NOTE: My wall studs were off center resulting in my mount being off center where I wanted to mount my TV. Rather than opening up the wall and inserting bolts, I attached them to the existing locations by offsetting the bracket about 4 inches off center. The great thing about this mount is that I

I needed a wall mount for my 32" Panasonic Viera that swivels in all directions yet is sturdy. Received this yesterday and thought it was hard to take and heavy due to its own weight I marked the studs, drilled 4 holes, took a 4-screw DeWalt screwdriver, slung it over my shoulder and screwed the screws in. Next four screws on the back of the TV, immediately to the Hooks hung, set screws adjusted and I can tilt, rotate, extend, slide back the TV as easily as possible. I say it can hold up to 50"

I used this to install a 50 inch Panasonic plasma monitor (TC-P50S2) in November 2010. The bracket arrived very quickly (in California) and was undamaged. I had a small issue with the length of the screws, assuming the brackets are attached to the back of the TV. When I called Panasonic to confirm the length of the screws used check , they recommended 15mm which was not included. After checking the depth of the holes on the back of the TV, I found that 20mm would be enough to hold the TV…

I bought this Panasonic 50 inch plasma wall mount. As described, it is VERY solid and heavy or some other weak area. The levers are a little stiff to operate, which is good because you don't want your TV to move in the wind. It would be nice to get a helping hand when aligning the position on the wall as the whole unit is heavy. On to the cons: 1. First of all, the obvious problem is the distance between the wall plate mounting holes. The spacing between the outermost mounting slots is exactly…