📷 Universal Outdoor Camera Sun Rain Shade Cover Shield - SDS DS-1250ZJ Review

product well made. I used my own screws (3 inch). Installed above the garage in plaster. My Blink XT has an aftermarket mounting bracket so it protrudes further. It still fits. The chamber has a temperature. daylight difference. It was. On camera it dropped 13* degrees. The problem I had was that the camera got hot in direct sunlight, it didn't always work. So far so good with this screen!

I bought this to cover an external camera that was rated weatherproof but not waterproof. The recommended installation was under a canopy where it would be protected from direct impact. This screen was very easy to install. No hassle or fuss. Anyway, it would be great if it was a little deeper, but I have no complaints. dry chamber.

Overall it works very well. I had two hits on him. Firstly the underside is black but not matte, I sprayed it before trying it with night vision. It might have worked, but I got out high enough that I didn't want to mess with it twice. It's also a little smaller than I would like. I had to mount the camera off center and at a pretty good angle to fully adjust it. I only used a standard EZVIZ running camera, so definitely not suitable for a large camera.

Okay, this may sound silly, but I bought a lampshade to protect an external low-voltage transformer for landscape lighting. The transformer was installed under the spot where rainwater flows from the roof of the house. Moving the transformer is not an option. The rain hood fits perfectly and not only protects the transformer but also helps hide it from a plain black box. With a bit of skill I attached a photo light sensor to the side of the lampshade. I dyed the shade to match the color of the…

We were looking for a shade for our ring cameras that were exposed to inclement weather. I am so glad I found this product. That's exactly what we needed. It protects the camera from direct sunlight, offers rain/snow protection and most importantly is matte black on the inside to prevent light reflections from the lights of the camera/night vision. Installation was very easy and took about 10 minutes. The product also has a thin seal where it attaches to the house to prevent water from dripping

Very nice hood for nest camera. Protects against rain when you mount the camera on a wall where it is not under a roof. But let me warn you about my own mistakes. Do not mount the camera as high under the hood as in the stock photo. I didn't even get mine that high underneath and I had to lower them anyway. What will happen is that it will cause a halo effect in the middle of the screen. This is due to the reflection of IR light from the underside of the hood. Although you couldn't see the…

I used mine for night owl cameras. Brilliant black. And a reflection from the bottom of the 1 inch wide white border that extends to the bottom of the hood. In both cases I painted the underside white and black with "FLAT BLACK". In addition to the halo, changes to the infrared LED motion detector caused it to REPORT MOTION ALERT. And it then enabled recording videos on the hard drive of the NVR 2T. The result was a huge amount of data that was captured and filled my hard drive. Also means that

Installed on a May Travel Trailer. It is the right size and offers good sun/rain protection. Here are the keys to a fun assembly success: 1. Apply masking tape where you are likely to drill holes (this will prevent soldering of the fiberglass) 2. Place the dome low over the camera and apply the tape in place 2. Make sure you have a good connection to your video screen and that the camera is not blocked. 3. Mark the holes on the masking tape. 4. Find something smaller than the screws, drill the…

I bought this for my Hikvision ColorVu camera to protect it from the sun and rain. That's a lot of money for just one piece of plastic! My main issue is that my camera has a 2.8mm lens (wide angle) so I had to move the screen around the camera a lot so it doesn't interfere with the view at the edges, which drastically reduces the intended protective purpose of the camera. Even after raising the shield, I was still blinded by the camera's built-in light because the edge of the shield is white. I