🚗 Rough Country Neoprene Seat Covers Set - Black [Chevy Silverado 1500] 1999-2006 Front/Rear 91019: Water Resistant, Durable Protection Review

Super clean fit, I really couldn't have asked for a better fit, straps are quite strong, quality zips and velcro. I wish this applied more to a neoprene material like a wetsuit, but it looks like it will last for years. It's a work truck, so I'll put it to the test.

They look and feel good! They're not a quick and easy install, but at the same time, it's not impossible. It took me and my friend about 2 hours to install them in my Silverado stretch cab. The rear seat had to be removed to properly cover it. Although it looks great and is the best I've ever had. I will decide on a repurchase in due course.

Seat covers are great love them. Installation takes a bit - about half an hour per front seat (stretching and pulling), but I'm a bit picky. The back seat takes about an hour - I detached the seat from the back of the cab. You will need to remove the nuts from the floor brackets. the seat is then lifted out of the sliding brackets on the back. Overall great look and comfort. Worth the time and money!

My husband has power seats and they don't have cut outs for all the buttons, looks cool. I'm going to swap out the undersides of the front seats to completely cover the area so there isn't a random hole where the seat handle would normally fit. They cover the back of the rear seat and therefore need to be removed to fully install the seat covers. Make sure you have a paperclip or eyeglass screwdriver to remove the headrest (I think that's a good idea).

I was debating whether or not to remove the seats so I decided to try without removing the seats. It took me a while to install the side seat trim but somehow I managed to put it back on lol. All in all we are worth it! Absolutely in love with these seat covers! Installed on my 03 GMC Sierra Ext Cab. Ps- if you find it difficult to thread the center seat belts under the seat and out the other side, take a piece of metal wire, insert it and pull on the belt.

2003 Silverado 1500 WT These cases seem great, they look great and they fit well. The easiest install we found was to remove the back seat. We started with all the seats, but we had to put the front seats back and it turned out to be easier. You will need a small needle to pry the headrest out. The center front cover does not fit well with the work truck center front seat (see picture, it slides off very easily), we plan to replace it with a console. In general, the appearance of the truck has…

They appear to be of good quality and very comfortable. However, to properly install them you must remove the seats, which in my case, as I owned a 2000 Chevrolet Silverado 1500, required me to purchase a set of specialized sockets (my shop didn't have separate sockets, so I had to order a set buy.) In my case I needed E14 and E20 plugs to remove the front seats, something like a torque plug (spelling?) and an 18mm plug for the rear seat. Some basic installation instructions would have been…

Seat covers have a pretty solid feel and are very comfortable, but the only criticism I have of navy covers is that they are a bit difficult to put on when you If you have an extended cab, the rear seat will be a bit difficult to install as one of the brackets holding the seat to the rear frame is too long to pull the seat out. Backrest so you can put the cover on the seat so you need to cut it off. In general, I like the marine cases very much and they have suffered a lot, but they still look…

The seat covers fit perfectly so I highly recommend this product. Keep in mind that no instructions are included, but you should be able to figure out how to install it by looking at the individual parts. Installing the rear seat covers will not be easy either, since the backrest in the 2005 Silverado cannot be lowered down onto the seat. I tried to remove the back seat (bench) but gave up. My advice: do not open the two ends of the case. Instead, pull the entire cover toward the seat by the…