🔩 Power Transmission Products
2 Review
Flexible rubber parallel coupling that fits with steel piping, copper, cast iron, plastic, copper and lead. Applications include non-pressure drain, waste, and vent piping systems and sewer systems indoors and outdoors. Sealed leak-proof flexible connectors with stainless steel clamps that will last. Double fitting size: 1-1/2” x 1-1/2”. Conforms to…
Read more about this product
2 Review
2pcs Flange Shaft Coupling, suitable for model shaft connection, it is a good accessory for stepper motor, RC model motor, DIY model making etc. Cylinder Size (IDxODxH): 3*10*10mm, Base Size (DxH): 22*2mm, Fastening Screw Hole: M3, Base Mounting Screw Hole: M3, Base Hole Pitch: 16mm. Made of 45# steel, hardened by heat treatment, and then electroplated…
Read more about this product
2 Review
Mini Nylon Ball Transfer Unit are omni-directional load-bearing spherical balls mounted inside a restraining fixture; 360 universal transfer bearing. With a load bearing capacity of 4.4 lbs each, and maximum 6.6 lbs. They are made of high quality nylon, lightweight,smoothly. The diameter of rotated ball: 1/3 inch, the top diameter of base: 4/7 inch, the…
Read more about this product
2 Review
Single pin and block universal joint for applications with up to 25 degrees angular misalignment and speeds up to 1,750 RPM. Compensates for angular misalignments and shaft separation. Steel for strength and durability. Bored hubs fit onto shafts without the need for machining. Operating temperatures range from -30 to 212 degrees F.
2 Review
Arlington's bushings fit existing irregular shaped holes in metal studs. Comply with NEC code. Snap bushing and washer end together. Red in color, 100-Pack. UL approved.
2 Review
Connection Diameter: 8mm to 10mm, Total Length: 22mm /0.87 inch, Outside Diameter : 16mm/ 0.63 inch. Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies. Top tight type rigid…
Read more about this product
2 Review
3/8" (9.525mm) in diameter. Made of High Precision Brass. Smooth surface precision balls. Lightly lubricated. Good hardness and corrosion resistance. Package includes 10 piece balls.
2 Review
6 inch stroke length, 10 inch(255mm) retracted length, 16 inch(405mm) extended length. 165Lbs(750N) Maximum Load. No-load speed:10mm per sec. 6mm diameter mounting holes. Built-in limit switch. Protection class IP54, incomplete waterproofing. Maximum current 3A. Please pay attention to the dimension of product, SEE DIMENSIONAL DRAWING AND ADDITIONAL…
Read more about this product
2 Review
Initial and relubrication of rotor bearings in wind power stations. Relubrication of generator bearings. Constant velocity joints in lateral and longitudinal shafts of vehicles. Rolling and plain bearings subject to high loads, vibrations and oscillations.
2 Review
Shows level of oil in reservoir. Oil Eye Sight can be added. Item Package Dimension: 6.5" L x 1.5" W x 2.0" H. Item Package Weight: 0.75 lb
2 Review
Size: Lead Screw dia: 8mm, Pitch: 2mm, Lead: 8mm; two M3 holes centre distance is 18mm. Design:Anti-backlash spring loaded nut, high precision. Durable: Made of 100% brass material, resistant to corrosion and rust, sturdy. Application: Suitable for 3D Printer T8 Lead Screw. Package: Includes 2 sets Anti-Backlash brass nut.
2 Review
The hole diameter of the item is up to standard,which is good for application. Good anti-corrosion function helps prevent rust during transportation and storage process. Low friction resistance and high speed features,a good choice for you. The bearing well lubricated can runs smoothly and efficiently. Inner Diameter:12mm / 0.47"(ID);Outer Diameter:28mm…
Read more about this product
2 Review
Dimensions: 35x72x17. Rubber seal on both sides. 100% Chrome Steel for higher resistance and durability. Supports 9,000 rpm. Our high-quality bearing is made to reduce your replacement frequency and maintenance cost.
2 Review
Straight miter 90 degree mesh transmits mechanical power between perpendicular shafts. Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles. Low carbon steel (.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to…
Read more about this product
2 Review
Stem Diameter: 0.625". Country Of Origin: United States. Material: Steel. Model Number: NAR10.
2 Review
Compatible with most 1/10 and 1/8 scale shocks. High quality aluminum construction,lightweight and durable. Easy captures shock shafts and shock bodies. Integrated shock end ball installer,feature the ability to pop the shock end pillow ball in and out of place. Advanced design for direct pressure feel,makes removing shock ends and doing shock…
Read more about this product
2 Review
LM6UU Linear Bearing Ball Bushing for 3D Printer. Package include:6 Pcs. Brand Listing, If you buy is not OctagonStar brand product, You Can Apply for a Refund and Compensation.
2 Review
This heavy duty linear actuator is a powerful solution for lifting large loads. With a max static load of 770 lbs and 385 lb max dynamic load - 4" 12 volt DC linear actuator. Specifications: 12 volt DC [electrical], 770 lb max [static load]; 385 lb max [dynamic load], [Speed]: 7mm/sec @ 50% Load - 8mm/sec @ no load, Current: 1 [Amp Draw] @ no load…
Read more about this product
2 Review
Straight miter 90 degree mesh transmits mechanical power between perpendicular shafts. Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles. High carbon steel for tensile strength and hardness. Country of origin: China.
