Header banner
Revain logoHome Page
πŸ› οΈ efficient and versatile uxcell straight shank 14.5mm drill for all your drilling needs logo

πŸ› οΈ Efficient and Versatile Uxcell Straight Shank 14.5mm Drill for All Your Drilling Needs Review

3

Β·

Poor

Revainrating 2.5 out of 5Β Β 
RatingΒ 
2.3
πŸͺš Industrial Drill Bits, πŸ”ͺ Cutting Tools

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ› οΈ Efficient and Versatile Uxcell Straight Shank 14.5mm Drill for All Your Drilling Needs
img 2 attached to πŸ› οΈ Efficient and Versatile Uxcell Straight Shank 14.5mm Drill for All Your Drilling Needs
img 3 attached to πŸ› οΈ Efficient and Versatile Uxcell Straight Shank 14.5mm Drill for All Your Drilling Needs
img 4 attached to πŸ› οΈ Efficient and Versatile Uxcell Straight Shank 14.5mm Drill for All Your Drilling Needs

Description of πŸ› οΈ Efficient and Versatile Uxcell Straight Shank 14.5mm Drill for All Your Drilling Needs

High Speed Steel tool - 14.5mm cutting diameter. Good for most general purpose applications, featuring a combination of hardness and toughness for wear resistance. Reduced Shank - Expanding the size range capacity of a portable drill chuck. Common flute and overall length for minimal adjustment during tool changes. Black Oxide Finish - Black oxide treatment adds lubricity. Small pockets on the surface of the tool that act to hold coolant near the cutting edge. Wide Application - Design for drilling in low and medium tensile strength materials, such aluminum, iron, copper, brass and metal. Please Note: To make clean and precise holes, water is required for lubrication and cooling when drilling metals. Increased use of water lubrication will extend drill bit life.

Reviews

Global ratings 3
  • 5
    0
  • 4
    1
  • 3
    0
  • 2
    1
  • 1
    1

Type of review

Revainrating 4 out of 5

A little sloppy.

14.5mm Drill: 13.52mm tip, half 14.43mm, chuck side of drill used is 15.23mm. I was concerned that I wouldn't get a 14.5mm hole, but the drill bit was so sloppy that it turned at a 1-2mm pitch. Overall I have a 15.2mm hole with a "14.5mm bit". Luckily my project didn't require precision.

Pros
  • Easy installation
Cons
  • There are other interesting options.

Revainrating 2 out of 5

Good value for money

This drill worked well until the reduced diameter shank bent when the drill caught it while drilling. With some effort I was able to straighten the shank enough to continue using it, but I would like the shank diameter to be increased to 1/2 inch for added strength. However, it was good value for money.

Pros
  • One year trial
Cons
  • Available in white only

Revainrating 1 out of 5

Not even worth the low price.

The drill was very close to the stated size. That's the only positive thing I can say about it. Even with a center punch, the drill moves uncontrollably. It's not piloted at all. Even after drilling a 1/2" pilot hole, this drill didn't cut through. Drill through 1/4" 304 stainless steel. Punched because I needed a hole but I basically burned it through, almost no chips just powder. I will never buy this brand again. Especially if the hole is critical to your project , invest in a reliable…

Pros
  • Nice packaging
Cons
  • I don't remember