🦈 Enhance Aero Performance with Alpha Racing 10pcs/Set Diffuser Shark Fin Kit and Spoiler Roof Wing Air Vortex Generator in Carbon Fiber Pattern Review

The picture is correct as far as the glue is applied. You look good. Will have this until I can afford $100. There for a week. car wash done. You still look good.

Put them on my car and they looked really ghetto rice I left 2 on to protect my antenna from side damage but the whole kit is kind of a waste if you want to put splitters on your car don't skimp on it.

Ordered these and they arrived the next day, very happy with them. I didn't like the look of carbon fiber so I painted them black and they came out pretty darn good. I'm very happy with the look and I definitely feel a big difference when riding in terms of stability and control. I wish they were already painted black and not just the carbon fiber option, but spray paint would have worked just fine. Overall a pretty good buy.

I was dying to put them on my car when I saw some YouTube videos of them. I was happy when my package arrived but was very disappointed when I opened the box and started looking at them and they did not match the advertised image (the image matched the spikes in the video) - I ordered the carbon Spikes. and after looking at them once i was very upset to see that they didn't even match the weave in the picture maybe just bad luck? But I will return these anyway

High gloss cheap plastic. I have not used them as they are too high above the roof surface. The slats are very flat and cannot follow the natural curvature of the roof, causing the leading and trailing edges to already peel off. The glue used is too long and leaves a 2mm difference between the surface and the body of the fin, giving it a cheap look. The photos show the dimensions of what I received as there are reviews showing different specifications. Usage is completely flat and people won't…

I have a Prius and certainly not the fastest car on the road. One of the main issues I struggled with was that the car bounced around a bit whenever I approached a large truck on the freeway, directly behind it, or in the adjacent lane. Not to the point where I lose control, but it's quite annoying. As a longtime Formula 1 fan, I think it's probably air turbulence and I could do something to disrupt the airflow and decided to give the shark fin a try. So I attached 4 pieces above the rear…

Great buy! Installation = 4 inch clearance - just before the end of the roof and the start of the slope - the last 4 inches of the roof. IMPORTANT --- install 15*offset from centerline - each side faces front to centerline. EXCEPT outside point on each side parallel to center line (straight on). Less than 3 inches apart = vortices cancel each other out without interfering with the next. Over 6 inches and not used by VGs due to the undisturbed linear airflow between them. An offset of 12-18* is…

I have a Prius and I'm sure it's not the most nimble car on the road. One of the main issues I struggled with was that the car bounced around a bit whenever I approached a large truck on the freeway, directly behind it, or in the adjacent lane. Not to the point where I lose control, but it's quite annoying. As a longtime Formula 1 fan, I think it's probably air turbulence and I could do something to disrupt the airflow and decided to give the shark fin a try. So I attached 4 pieces above the…

I bought these for my 2007 Tuscani (Hyundai) Tiburon. It's quite a long process to install if you do it "right". I installed vortex generators in the trunk of my hatchback. I used a roll of tailor's tape to line everything up and a roll of masking tape to make the marks. (A marker was also used.) I used a tape measure to find the size and divided that measurement (about 125cm) by 11 (11 divisions of 10 lines to center the pieces) and found that each Center piece 113mm long each would be from a…

Good buy! Installation = 4 inch clearance - just before the end of the roof and the start of the slope - the last 4 inches of the roof. IMPORTANT --- install 15*offset from centerline - each side faces front to centerline. EXCEPT outside point on each side parallel to center line (straight on). Less than 3 inches apart = vortices cancel each other out without interfering with the next. Over 6 inches and not used by VGs due to the undisturbed linear airflow between them. An offset of 12-18* is…