Header banner
Revain logoHome Page
๐Ÿ”ง hps performance 3/8" stainless steel fuel injection hose clamps (14mm - 16mm) - pack of 10 (fic-14x10) logo

๐Ÿ”ง HPS Performance 3/8" Stainless Steel Fuel Injection Hose Clamps (14mm - 16mm) - Pack of 10 (FIC-14x10) Review

9

ยท

Very good

Revainrating 4.5 out of 5ย ย 
Ratingย 
4.4
๐Ÿ”ง Car Belts, Hoses & Pulleys, ๐ŸŽ๏ธ Performance Car Parts & Accessories

View on AmazonView on ะฏM

Media

(3)
img 1 attached to ๐Ÿ”ง HPS Performance 3/8" Stainless Steel Fuel Injection Hose Clamps (14mm - 16mm) - Pack of 10 (FIC-14x10)
img 2 attached to ๐Ÿ”ง HPS Performance 3/8" Stainless Steel Fuel Injection Hose Clamps (14mm - 16mm) - Pack of 10 (FIC-14x10)
img 3 attached to ๐Ÿ”ง HPS Performance 3/8" Stainless Steel Fuel Injection Hose Clamps (14mm - 16mm) - Pack of 10 (FIC-14x10)

Description of ๐Ÿ”ง HPS Performance 3/8" Stainless Steel Fuel Injection Hose Clamps (14mm - 16mm) - Pack of 10 (FIC-14x10)

Sae # 15. Effective diameter range: 35/64" - 5/8" (14Mm - 16Mm). Made of 100 percent stainless steel. Better corrosion resistance compared to the standard zinc plated clamps. Smooth interiors prevent the clamp cutting the hose. Ideal for fuel lines and small diameter hoses. 9mm (3/8") band , 7mm slotted hex head ; Maximum Torque Spec: 13 in lbs. Exceeds all sae requirements. Sold in box of 10.

Reviews

Global ratings 9
  • 5
    7
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 5 out of 5

Good quality, rounded edge does no harm.

good quality, rounded edge will not damage the fuel hoses, much easier to install and remove than the originals in our Mercedes Sprinter

Pros
  • Free for educational purposes
Cons
  • Doubtful

Revainrating 5 out of 5

BEST THING YOU CAN BUY Clamps and Bushings

I USE THESE AND THE LARGER WHEN I RESTORE A VEHICLE I WORK ON. THIS IS WITHOUT A DOUBT THE BEST THING YOU CAN BUY! THE CHEAPER CLAMPS I HAVE TRYED ARE ONLY REMOVED WHEN I TRY TO TIGHTEN THEM.

Pros
  • Multiple competitors
Cons
  • Long shipping time

Revainrating 5 out of 5

Better seal than stock hose clamps

Uses these on new oil cooler power steering return lines. There were problems with the complete sealing of the "worm gear" type. They apply an even 360ยบ pressure around the hose to ensure a complete seal!

Pros
  • Great for me
Cons
  • Very expensive

Revainrating 5 out of 5

The best clamps for fuel line repairs.

Very good for replacing sections of corroded fuel lines and vapor return lines that require a combination fuel injection hose and flared nibble line. The socket wire ends with double clamps (pair) on each end, no leakage.

Pros
  • Excellent Overall Performance
Cons
  • I'll get back to you

Revainrating 5 out of 5

Good quality but READ DESCRIPTION again. the size.

High quality stainless steel clips. Just note that 3/8 inch is the width of the strap, NOT the diameter. They are suitable for max. 5/8 inch. hose OD I wasn't paying attention when ordering, but that was my fault. Fortunately, I also needed this size for another project.

Pros
  • Elegant design
Cons
  • Zero

Revainrating 1 out of 5

Should only fit the specified hose.

I have a Napa gas hose with fuel injectors printed on the skin. Some barely fit in, some didn't. I can't imagine they would fit regular 3/8" hose as they will NOT fit 1/2" OD as advertised. I love brackets but they are useless to me. waste of money.

Pros
  • Hands-Free Operation
Cons
  • Frequency

Revainrating 4 out of 5

Excellent terminals

They will fit a Gates 3/8" transmission coolant hose when fully open. No problem. Uh, edited. They will fit the hose, but if you have the hose on a steel pipe (like my power steering pump I tried today got).) is a bear for closing. You can't start the screw if you let it come out of the thread. Half an hour or more of struggling with this, the screw finally started with the edge of the clamp on the edge of the hose.

Pros
  • Satisfied so far
Cons
  • There are other interesting options.

Revainrating 5 out of 5

Great brackets!

I just added a transmission cooler and power steering cooler to my jeep. I did this particular upgrade on three jeeps. I used Gates 3/8 inch transmission hose rated at 400psi. These 3/8 inch stainless steel clamps work well although they are tight. So they definitely won't fit a larger hose, but are perfect for 11/32" or 3/8". The clamps look neat and clean and provide a great, even seal. Unlike cheap worm drive clamps, there is no extra protruding clamp to look like crap or irritate yourโ€ฆ

Pros
  • Easy Install
Cons
  • Something else

Revainrating 5 out of 5

Real stainless steel

I bought these clamps after buying another pack of 10 clamps that claimed they were "stainless steel" when they weren't. Revain has since made corrections to the falsely advertised clamps sold by Autokay. Nonetheless, these clamps worked great for installing an additional transmission cooler on a Jeep Wrangler TJ. These are indeed stainless steel clamps and fit 3/8 inner diameter. Transmission hose or fuel hose. I've read some reviews saying they are very difficult to stop or barely fit in aโ€ฆ

Pros
  • cool product
Cons
  • Clarity