Review on 🎮 ASUS ROG X570 Crosshair VIII Hero Wi-Fi ATX Motherboard with PCIe 4.0, on-Board WiFi 6 (802.11Ax), 2.5 Gbps LAN, USB 3.2, SATA, M.2, Node and Aura Sync RGB Lighting by Stanisaw Augustynowi ᠌

Name: 🎮 ASUS ROG X570 Crosshair VIII Hero Wi-Fi ATX Motherboard with PCIe 4.0, on-Board WiFi 6 (802.11Ax), 2.5 Gbps LAN, USB 3.2, SATA, M.2, Node and Aura Sync RGB Lighting
Item: 🎮 ASUS ROG X570 Crosshair VIII Hero Wi-Fi ATX Motherboard with PCIe 4.0, on-Board WiFi 6 (802.11Ax), 2.5 Gbps LAN, USB 3.2, SATA, M.2, Node and Aura Sync RGB Lighting
Rating: 5

July 04, 2023

I am one hundred percent satisfied with the purchase, I recommend this product to everyone.

I am 100% satisfied. It allows you to open 5950x to the maximum, while everything is by default out of the box. Everything is configured in 30 minutes.
Bios is 2022 - but what is strange, when you turn on 2022 - half of the settings for overclockers disappear. I don't understand why, and I don't care. Not a minus for me.
In the reviews, there are a hundred manuals for how an amateur can set everything up the first time. On non-top boards, as a rule, there are almost no reviews, or they are very dry.
Free Tip for 20% acceleration about which no one writes anywhere - put the system and the main pies on m2 with pcl4 (namely revision 4).
! And the most important - m2 with the system and so on must be installed in a short slot - which goes to the processor, not to the chipset.
Once again - m2 slots on the board 2 pcs. One goes to the chipset and the other goes to the processor.
Asus writes that there is no difference - but in fact the same disk gives a difference of 15-20% in speed, install it on a bunch of m2 - Cpu.
If you have a standard water pump - (you will not cool the 5950x with fans and  your ears) - do not connect a pump to the 3a pins. Connect to aio wp- at 3 amps my pump from be quiet goes crazy, behaves incorrectly. I set it to 1 ampere - everything works properly, it is controlled via qfan.
PS. Power - I think it's clear that everything works at maximum speed, you need to connect ALL power slots - 24 + 8 + 4, the board will start up at 24, but then you shouldn't be surprised that the indicators sag somewhere.

Pros

1. Top board. 2. Power allows you to squeeze the maximum from 5950x. And there are only 3-4 such boards on the market. 3. M2 works with pcle protocol 4. Get a multiple increase in speed. 4. If the task is overclocking, everything is here. And boost and nutrition. You can drive above 90 amperes in a clean percentage, and these are collosal currents. 5. Pive cooling - at maximum loads it does not go above 50 degrees. No noisy chipset fans. 6. Lineup. Everything starts without problems. 6. Considered to be the perfect finalized motherboard for socket am4.

Cons

1. Price? 2. At the first embly and launch - without a connected gpu and monitor, do not be afraid of errors and postcodes. Just plug in a monitor. I decided to check the embly without a monitor using post codes - on the first run I was surprised by the errors. 3. Strange, but I did not have enough connectors for fans, although there seem to be quite a lot of them. The last 2 fans came to be installed through the 2-1 adapter.