Header banner
Revain logoHome Page
πŸ€– daoki dual h-bridge robot motor drive controller board for arduino smart car - stepper motor control module with dupont cable logo

πŸ€– DAOKI Dual H-Bridge Robot Motor Drive Controller Board for Arduino Smart Car - Stepper Motor Control Module with Dupont Cable Review

7

Β·

Excellent

Revainrating 5 out of 5Β Β 
RatingΒ 
5.0
πŸ–₯️. Single Board Computers, πŸ’» Computer Components

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ€– DAOKI Dual H-Bridge Robot Motor Drive Controller Board for Arduino Smart Car - Stepper Motor Control Module with Dupont Cable
img 2 attached to πŸ€– DAOKI Dual H-Bridge Robot Motor Drive Controller Board for Arduino Smart Car - Stepper Motor Control Module with Dupont Cable
img 3 attached to πŸ€– DAOKI Dual H-Bridge Robot Motor Drive Controller Board for Arduino Smart Car - Stepper Motor Control Module with Dupont Cable
img 4 attached to πŸ€– DAOKI Dual H-Bridge Robot Motor Drive Controller Board for Arduino Smart Car - Stepper Motor Control Module with Dupont Cable

Description of πŸ€– DAOKI Dual H-Bridge Robot Motor Drive Controller Board for Arduino Smart Car - Stepper Motor Control Module with Dupont Cable

The signal is shown in the figure. The connecting method is shown inbelow figure after enable ENA ENB. Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled. Package Content: 2 x L298N Motor Drive Controller Board, 1 x 11.8" male-FeMale Dupont Cables 12 PIN, 1 x 11.8" Male-Male Dupont Cables 12 PIN, 1 x 19.6" 28AWG Wire.

Reviews

Global ratings 7
  • 5
    7
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

A good buy for experimental purposes.

Easily handles 1.5 amps of continuous use for two consecutive months. I use them to control motors to turn them into variable speed pumps. Make sure you cover the boards with something waterproof if you intend to use them outdoors.

Pros
  • Electronics
Cons
  • Some small things

Revainrating 5 out of 5

Drivers as advertised

For value for money I would give 5 stars but the product did not come with specifications. It would be nice to have a spec in the future so I don't have to look it up online.

Pros
  • Computers and accessories
Cons
  • There are cons

Revainrating 5 out of 5

Excellent H-Bridges. I control it with Raspberry Pi.

Great H-bridges. I control them with Raspberry Pi with no problem. I wish they had made one of these that can handle high current. I usually have to run about 4 of these in parallel to run a 10 amp, 12 volt motor without getting hot. But they work great in parallel.

Pros
  • Single board computer
Cons
  • Lots of stuff

Revainrating 5 out of 5

Excellent H-Bridges. I control them with Raspberry Pi.

large H-Axes. I control them with my Raspberry Pi with no problems. I wish they had made one of these that could handle more current. I usually have to run about 4 of these in parallel to to drive a 10 amp 12 volt motor without getting hot.. But they work great in parallel.

Pros
  • Package Contents: 2 x L298N Motor Drive Controller Board, 1 x 11.8" Dupont Connector Cable, 12-pin, 1 x 11.8" Dupont Connector Cable, 12-pin, 1 x 19, 6" wire 28AWG
Cons
  • For old

Revainrating 5 out of 5

These little bugs work great!

Ideal for working with a variable capacitor for mains tuning. Apply 0-5V PWM signal to IN1 or IN2 for left motor and switch to reverse direction. Apply 0-5V PWM signal to IN3 or IN4 for right motor and switch to reverse direction

Pros
  • Signal in picture
Cons
  • Volume

Revainrating 5 out of 5

The driver is as advertised

I would give 5 stars for value for money but the item did not come with specification. It would be nice to have a spec in the future so I don't have to look it up online.

Pros
  • . DC motor control Because the module is controlled by a double H-bridge, it can control two motors at the same time.
Cons
  • No performance

Revainrating 5 out of 5

A good buy for experimental purposes.

Easily withstands 1.5 amps of continuous use for two consecutive months. I use them to control motors to turn them into variable speed pumps. Make sure you cover the boards with something waterproof if you intend to use them outdoors.

Pros
  • The connection method is shown in the following figure after turning on ENA. ENB
Cons
  • Updates