Header banner
Revain logoHome Page
enhanced ender 3 linear rail guide kit with stainless steel mgn12c carriage block and slider for 3d printers - compatible with creality ender 3/pro/v2 (300mm, c-type) logo

Enhanced Ender 3 Linear Rail Guide Kit With Stainless Steel MGN12C Carriage Block And Slider For 3D Printers - Compatible With Creality Ender 3/Pro/V2 (300Mm, C-Type) Review

2

·

Average

·

$$
Revainrating 3.5 out of 5  
Rating 
3.5
🔧 Linear Motion Products, 🔩 Power Transmission Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to Enhanced Ender 3 Linear Rail Guide Kit With Stainless Steel MGN12C Carriage Block And Slider For 3D Printers - Compatible With Creality Ender 3/Pro/V2 (300Mm, C-Type)
img 2 attached to Enhanced Ender 3 Linear Rail Guide Kit With Stainless Steel MGN12C Carriage Block And Slider For 3D Printers - Compatible With Creality Ender 3/Pro/V2 (300Mm, C-Type)
img 3 attached to Enhanced Ender 3 Linear Rail Guide Kit With Stainless Steel MGN12C Carriage Block And Slider For 3D Printers - Compatible With Creality Ender 3/Pro/V2 (300Mm, C-Type)
img 4 attached to Enhanced Ender 3 Linear Rail Guide Kit With Stainless Steel MGN12C Carriage Block And Slider For 3D Printers - Compatible With Creality Ender 3/Pro/V2 (300Mm, C-Type)

Description of Enhanced Ender 3 Linear Rail Guide Kit With Stainless Steel MGN12C Carriage Block And Slider For 3D Printers - Compatible With Creality Ender 3/Pro/V2 (300Mm, C-Type)

The X axis linear rail kit is special designed for Ender 3, Ender 3 Pro, Ender 3 V2. 【High Qaulity Linear Bearing】the sliding ball is made of high quality steel, wear resistant, low noise, smoother and efficient operation. 【High Precision】high strength, low noise, high speed, long service life. 【Rubber Stopper】with rubber plug on the both side of linear rail to prevent the sliding block from falling out. 【Easy to Install】Together with extruder back plate, T-nuts and screws, hex key for easy installation.

Reviews

Global ratings 2
  • 5
    0
  • 4
    1
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 4 out of 5

Works as it should.

Everything fits well. As with any upgrade to a 3D printer it takes a little finesse to get everything dialed in. The linear rails that come with this kit are low cost generic rails and require cleaning and lubricant but they work well. Check out YouTube for videos on how to do that.

Pros
  • If you upgrade to the slide rail you will need a longer belt.
Cons
  • The Enhanced Ender 3 Linear Rail Guide Kit is significantly more expensive than some of its competitors, making it less accessible to those on a budget

Revainrating 3 out of 5

Not exactly to Creality Ender 3 specz

At first glance appears to be good for the money, but there were issues. The replacement mounting plate is off by a few thousanths, which is just enough that a Bondtech DDX extruder will not fit onto it without modification. Had to oversize the holes in the Bondtech by a few thousanths each to make it fit properly. Also, the skies for the timing belt are set too far towards the center and the timing belt wouldn't fit with the stock tensioner attached. Had to get a hacksaw out and cut two new…

Pros
  • {}
Cons
  • Installation can be quite tricky and time-consuming, especially for those not familiar with 3D printer mechanics, which may make it unsuitable for beginners