Header banner
Revain logoHome Page
🔥 enhance your 3d printing: esun ebox lite upgraded filament dryer box for superior results logo

🔥 Enhance Your 3D Printing: ESUN EBOX Lite Upgraded Filament Dryer Box for Superior Results Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.3
🖨️ 3D Printing Supplies, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔥 Enhance Your 3D Printing: ESUN EBOX Lite Upgraded Filament Dryer Box for Superior Results
img 2 attached to 🔥 Enhance Your 3D Printing: ESUN EBOX Lite Upgraded Filament Dryer Box for Superior Results
img 3 attached to 🔥 Enhance Your 3D Printing: ESUN EBOX Lite Upgraded Filament Dryer Box for Superior Results
img 4 attached to 🔥 Enhance Your 3D Printing: ESUN EBOX Lite Upgraded Filament Dryer Box for Superior Results

Description of 🔥 Enhance Your 3D Printing: ESUN EBOX Lite Upgraded Filament Dryer Box for Superior Results

【Upgraded eBOX Lite Dryer Box】Moisture can cause printing failure, our eBOX Lite dry box is designed to keep filament in constant temperature and humidity, especially for those hygroscopic filaments. It can remove the excess moisture, keep the filament dry. 【Efficient Heating & Even Temperature】Upgraded Built-in PI heating Arc Sturcture and insulation cotton surrouding structure, eBOX Lite filament dryer box can heating fialment evenly and temperature inside the box can effectively reach 50°C-55°C in just 2 hours. Besides, it can maintain constant temperature and humidity all the time. 【Low Noise & Storaging】This storage dry box has applied upgraded long-life low-noise turbo fan, which can provide a quiet working environment even at night. Also it can provide a dry storage environment for filament. 【High Compatibility】Maximum capacity of the Dry box is 200*73mm, it works perfectly with 1.75mm/2.85mm/3.00mm diameters filament in 0.5kg/0.75kg/1kg. Transparent lid design is easy to check the filament without open the lid. 【Easy to Use】This dry box is very easy to use and have a inside temperature range between 40°C -55°C. It is temperature setting mode when press mode button setting from 1-3 by up/down button and mode button again for setting heating time from 0-18h.

Reviews

Global ratings 3
  • 5
    1
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 1 out of 5

Absolutely Terrible

Ordered one to store my filament. The first arrived with a huge crack in the pump, rendering it unusable. I ordered a replacement and it came with a broken pump! However the tear was quite small and the pump was still sucking a bit so I decided to give it a try - if it works I can glue it on with epoxy or super glue, no big deal. However, it didn't work. I tried to inflate the bag for several minutes but to no avail. Then I tried my Dyson vacuum - no luck. In desperation, I tried my shoppyk…

Pros
  • High Compatibility
Cons
  • Thin

Revainrating 4 out of 5

Best 3D Printing Consumables I've Found

PRO: The pockets are big enough to hold all my filaments. Others I tried were very dense. The pump is really good, good quality. The bags seem to be holding a vacuum so far. However, there is not much time to say for sure. I will come back and update in a week. CONS: The vacuum port has nothing to help you seal and remove air. So if you put it on a flat surface, you can't get it to pull the vacuum. If you can stick it on the edge of a spool of thread you can make it work, but it's not easy. I…

Pros
  • Quiet and Space Saving
Cons
  • Not bad, but...

Revainrating 5 out of 5

Great addition to PLA printers

eSun eBox is designed to dry PLA filaments during printing. Keeping the PLA filament dry is critical to getting the best prints. [Also, I keep each spool of filament in a sealed Sistema container with desiccant bags to keep the filaments dry.] To use, simply pop a desiccant bag or two into the back of the machine behind the fan (first photo). ), place the spool of thread on the two spools and close the cover. The thread runs through a small hole in the writing; eSun provides a guide that guides

Pros
  • Efficient heating and uniform temperature
Cons
  • Crumpled packaging