Header banner
Revain logoHome Page
πŸ”§ extreme max 3004.3093 45 degree base for slider trax / oem marine accessory mounting systems logo

πŸ”§ Extreme Max 3004.3093 45 Degree Base for Slider Trax / OEM Marine Accessory Mounting Systems Review

6

Β·

Average

Revainrating 3.5 out of 5Β Β 
RatingΒ 
3.5
πŸ‘¨β€πŸ’» Powersports Electronics, πŸš— Car & Vehicle Electronics

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ”§ Extreme Max 3004.3093 45 Degree Base for Slider Trax / OEM Marine Accessory Mounting Systems
img 2 attached to πŸ”§ Extreme Max 3004.3093 45 Degree Base for Slider Trax / OEM Marine Accessory Mounting Systems
img 3 attached to πŸ”§ Extreme Max 3004.3093 45 Degree Base for Slider Trax / OEM Marine Accessory Mounting Systems
img 4 attached to πŸ”§ Extreme Max 3004.3093 45 Degree Base for Slider Trax / OEM Marine Accessory Mounting Systems

Description of πŸ”§ Extreme Max 3004.3093 45 Degree Base for Slider Trax / OEM Marine Accessory Mounting Systems

For Boats with OEM Rails – The multi-fit design fits most boats pre-equipped with gunnel extrusions like Lund & G3. Works great with Lund Sport Trak. Construction – Bases are made of heavy-duty composite for maximum durability and corrosion-free life. OEM Approved – Available pre-installed on certain model boats from recognized OEM leaders. Options – Slider Trax bases and rails are sold separately to maximize ordering options. Warranty – 2-year replacement warranty.

Reviews

Global ratings 6
  • 5
    3
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    2

Type of review

Revainrating 5 out of 5

Does not fit: Electronics

Does not fit my Craft Pro Anger XL Smoker. The angle looked perfect when fitting into the rail system.

Pros
  • Best
Cons
  • Fits

Revainrating 1 out of 5

Easy to install and move

Easier to install than Lund factory at about half the price. Used it for an extra rod holder on my Lund boat.

Pros
  • Done
Cons
  • Upgrades

Revainrating 5 out of 5

Great rod holder bases

I used these on my 2014 Lund Impact with the SportTrack guide. Great fit. They fit snugly, so if you want to move them, it's easier to remove and reposition them. Be sure to measure the bases of the rod holders to make sure they fit.

Pros
  • Great price
Cons
  • Easy repairability

Revainrating 5 out of 5

Great product for your boat.

Works great but not as good as Factory Lund braces. To remove them, you need to unscrew the screw. But for the price, it's hard to beat. I installed my 1/2" mounts on all of them. Then I prepared various things for them. Also have them on your Spider Rig Rod Holders, Side Pull Holders, Catfishing 1/2" Rod Holders and Bait Cutting Boards.

Pros
  • Inspires confidence
Cons
  • Useless features

Revainrating 1 out of 5

Not worth 10€! good for mounting electronic devices

They fit my polar force rail system. I had to change the entire back robe to fit. I put them on after two hours. Very weak essay. When attempting to lift the rod holder to change its angle, this mount seemed about to pop. The base of the mount is barely wide enough to accommodate the recommended cannon rod holders. I had to drill holes in the rod holder and redo the base AGAIN. I believe most thrifty skin holders have the same base fit issue. 3 hours to install two rod holders, I take them off…

Pros
  • If satisfied
Cons
  • I'll write later