Header banner
Revain logoHome Page
🔌 keeyees usbasp downloader programmer set with cable, 10pin to 6pin adapter board - ideal for 51 & avr series microcontrollers logo

🔌 KeeYees USBASP Downloader Programmer Set with Cable, 10Pin to 6Pin Adapter Board - Ideal for 51 & AVR Series Microcontrollers Review

4

·

Very good

Revainrating 4 out of 5  
Rating 
4.0
🧰 Computer Internal Components, 💻 Computer Components

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔌 KeeYees USBASP Downloader Programmer Set with Cable, 10Pin to 6Pin Adapter Board - Ideal for 51 & AVR Series Microcontrollers
img 2 attached to 🔌 KeeYees USBASP Downloader Programmer Set with Cable, 10Pin to 6Pin Adapter Board - Ideal for 51 & AVR Series Microcontrollers
img 3 attached to 🔌 KeeYees USBASP Downloader Programmer Set with Cable, 10Pin to 6Pin Adapter Board - Ideal for 51 & AVR Series Microcontrollers
img 4 attached to 🔌 KeeYees USBASP Downloader Programmer Set with Cable, 10Pin to 6Pin Adapter Board - Ideal for 51 & AVR Series Microcontrollers

Description of 🔌 KeeYees USBASP Downloader Programmer Set with Cable, 10Pin to 6Pin Adapter Board - Ideal for 51 & AVR Series Microcontrollers

【Support 3.3V and 5V】: Supports 3.3V and 5V microcontrollers and circuit boards. The output voltage can be adjusted easily by the jumper cap!. 【Easy to Use】: Applicable to WIN8.1 / 8/7 / XP 32-bit / 64-bit computer. It can be directly connected to the USB interface of the computer, which is very convenient to use. (Please note: this product is not suitable for WIN10). 【Easy to Program】: Programming interface is reserved, you can upgrade the downloader firmware by yourself. Programming software: AVR_fighter, PROGISP1.66, PROGISP1.67, PROGISP1.68, can also compile lower or higher software, programming is very convenient. 【Automatic Speed Regulation】: AUTOSPEED automatic speed control firmware, the downloader will automatically track the frequency of the chip to be programmed and automatically change the speed to achieve automatic speed control. 【10PIN to 6PIN Converter】: Equipped with standard ATMEL ISP10 to ISP6 port converter.

Reviews

Global ratings 4
  • 5
    0
  • 4
    4
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 4 out of 5

First, have a working Arduino ready!

Buy these but make sure you have a working USB programmable Arduino first. Upload the public Arduino ISP sketch to an existing Arduino. Use this Arduino to flash modern M8 USBASP firmware to these two KeeYees ISPs. After that they can be used as usual.

Pros
  • I/O connector boards
Cons
  • Anything I can add

Revainrating 4 out of 5

Works great with Windows 10

Update firmware with"avrdude -C avrdude.conf -p atmega8 -c usbasp -U" flash:w:usbasp.atmega8.2011-05-28.hex :i "-F -P usb" and use the libusb-win32 driver and everything looks fine from a hardware point of view. Good deal for these as you will need a pair (2x) to perform the flashing above. You will also need to either solder the connectors to the JP2 location or electrically connect them in some way to "self-flash" each other as well. All in all a good deal for a couple!

Pros
  • Electronics
Cons
  • Fits

Revainrating 4 out of 5

Good programmer, firmware update needed out of the box

As other reviews have stated, you need a firmware update to support slow Sck and TPI. The last firmware update for them came out in 2011 so I'm puzzled why they don't ship that update. Luckily it's two packs and they don't need a slow sck to program, so you can just connect them back to back with one of the cables provided, short the JP2 with a short wire, connect the other to the computer and use avrdude to flash one , and then repeat the process in the other direction. However, once that's…

Pros
  • Computer components
Cons
  • Minor issues

Revainrating 4 out of 5

Worked great; no reprogramming needed

I was using avr-dude running in a linux virtual machine on my mac and it programmed a new chip from the factory. Worked great.

Pros
  • Serial cards
Cons
  • Ugly packaging