Header banner
Revain logoHome Page
πŸ”₯ kodiak cutting tools kct137388 premium: unrivaled performance for superior results! logo

πŸ”₯ Kodiak Cutting Tools KCT137388 Premium: Unrivaled Performance for Superior Results! Review

6

Β·

Average

Revainrating 3.5 out of 5Β Β 
RatingΒ 
3.7
πŸ”§ Milling Accessories, πŸ”ͺ Cutting Tools

View on AmazonView on Π―M

Media

(3)
img 1 attached to πŸ”₯ Kodiak Cutting Tools KCT137388 Premium: Unrivaled Performance for Superior Results!
img 2 attached to πŸ”₯ Kodiak Cutting Tools KCT137388 Premium: Unrivaled Performance for Superior Results!
img 3 attached to πŸ”₯ Kodiak Cutting Tools KCT137388 Premium: Unrivaled Performance for Superior Results!

Description of πŸ”₯ Kodiak Cutting Tools KCT137388 Premium: Unrivaled Performance for Superior Results!

Premium Sub-Micrograin Carbide End Mill Made In the USA. 1/4" Shank Diameter. 1-1/2" Flute Length (Length of Cut), 30 Degree Helix. 4" Overall Length Center Cutting Carbide Endmill. 2 Flutes, Single End.

Reviews

Global ratings 6
  • 5
    4
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    2

Type of review

Revainrating 1 out of 5

Nice and sharp but a little chatty

Bought this to cut a 2 3/8 guitar body. The bit cuts well, but wobbles a bit due to the length, which leads to breakouts. Cut very slowly with this bit. In general, he coped with the task.

Pros
  • New
Cons
  • Minor issues

Revainrating 5 out of 5

Great router! good for milling Accessory

I use this bit for deep pocket milling on my CNC. It's a special bit so I've only used it a couple of times, although I suppose you could use it as your main bit if you like. I have other shorter bits that I use mostly. I love having this little bit around.

Pros
  • good article
Cons
  • exchange available

Revainrating 5 out of 5

Good but slower for deep cuts

It's nice. I bought it to cut out a project in a picture. It was a hard walnut, 2 1/2 inches thick. The extra length caused a bit of vibration in the neckline and I had to slow down considerably and limit the neckline depth on each pass to get the job done. In fact, I was concerned that the racquet would break if it dangled if I ran too fast. I have no regrets, but this project was about all of that, but I wanted to do it. But I would again

Pros
  • Decent performance
Cons
  • Modern

Revainrating 1 out of 5

Garbage price

This is the first bad review I have ever written. First, I am very easy to use with my tools. I used this bit for a whopping 3-5 seconds before it broke. And it was $20! I might as well flush $20 down the toilet. By far the worst product I've bought from Amazon. Very very disappointed.

Pros
  • Industrial & Scientific
Cons
  • Not as thick as others

Revainrating 5 out of 5

Great router!

I use this cutter for CNC deep pocket milling. It's a special bit so I've only used it a couple of times, although I think you could use it as your main bit if you like. I have other shorter bits that I use mostly. I love having this little bit around.

Pros
  • Cutting tools
Cons
  • Discontinued model

Revainrating 5 out of 5

Good but slower for deep cuts

That's a nice moment. I bought it to cut out a project in a picture. It was a hard walnut, 2 1/2 inches thick. The extra length caused a little vibration in the cut and I had to slow down significantly and limit the depth of cut on each pass to get the job done. In fact, I was concerned that the racquet would break if it dangled if I ran too fast. I have no regrets, but this project was about all of that, but I wanted to do it. But I would again

Pros
  • Square nose
Cons
  • Something different