Header banner
Revain logoHome Page
๐Ÿ”‹ lgdehome 10pcs 1s 3.7v 4a 18650 charger pcb bms protection board for li-ion lithium battery cell: reliable battery safety and charging solution logo

๐Ÿ”‹ LGDehome 10PCS 1S 3.7V 4A 18650 Charger PCB BMS Protection Board for Li-ion Lithium Battery Cell: Reliable Battery Safety and Charging Solution Review

3

ยท

Very good

Revainrating 4.5 out of 5ย ย 
Ratingย 
4.3
๐Ÿ”Œ Household Battery Chargers, ๐Ÿงป Household Supplies

View on AmazonView on ะฏM

Media

(4)
img 1 attached to ๐Ÿ”‹ LGDehome 10PCS 1S 3.7V 4A 18650 Charger PCB BMS Protection Board for Li-ion Lithium Battery Cell: Reliable Battery Safety and Charging Solution
img 2 attached to ๐Ÿ”‹ LGDehome 10PCS 1S 3.7V 4A 18650 Charger PCB BMS Protection Board for Li-ion Lithium Battery Cell: Reliable Battery Safety and Charging Solution
img 3 attached to ๐Ÿ”‹ LGDehome 10PCS 1S 3.7V 4A 18650 Charger PCB BMS Protection Board for Li-ion Lithium Battery Cell: Reliable Battery Safety and Charging Solution
img 4 attached to ๐Ÿ”‹ LGDehome 10PCS 1S 3.7V 4A 18650 Charger PCB BMS Protection Board for Li-ion Lithium Battery Cell: Reliable Battery Safety and Charging Solution

Description of ๐Ÿ”‹ LGDehome 10PCS 1S 3.7V 4A 18650 Charger PCB BMS Protection Board for Li-ion Lithium Battery Cell: Reliable Battery Safety and Charging Solution

MULTIPLE PROTECTION:The module has 4 function:1.Overcharge protection, 2.over-discharge protection โ€˜3.short-circuit protection, 4.over-current protection; So the moule will allow long time using. you can finish your project perfectly. Charging voltage:4.2v:Max Working current:4A. How To Wire:B+: connected to battery positive, B-: connected to battery negative, P+: connected to charge / discharge positive, P- :connected to charge / discharge negative. LOW Consumption: MOS transistor can control the battery charge and discharge, low current . Wide Application:Widely used for solar street light battery pack,3.7V lithium batteries,LED light backup power supply etc.

Reviews

Global ratings 3
  • 5
    2
  • 4
    0
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Nice little 1s BMS - Chargers

These 1s BMS are just the right size. It is 1.75mm high, 37mm long and 4.15mm wide. It's small enough that you can flip an 18650 battery and you almost never see it. They're working well so far.

Pros
  • Electronics
Cons
  • write later

Revainrating 5 out of 5

Great Little Protection Panels

These great little panels are a huge hit. It would be nice to have ones available with solder tags already attached, but there's nothing a quick solder can't take care of.

Pros
  • Household Batteries, Chargers & Accessories
Cons
  • Expensive

Revainrating 3 out of 5

Charging worked fine, but no overcharge protection

Tested on 4 separate batteries. These batteries were discharged to 2.6V prior to charging. The board had no problem charging them fully. I purposely left a battery pack overnight to charge and the next morning it read 0V (low). Basically, the first charge went well, but there is no overcharge protection. I would recommend paying attention to loading when using these boards. The good thing is that these are 4A boards and they don't even get hot during the charging cycle.

Pros
  • Chargers
Cons
  • Some small things