Header banner
Revain logoHome Page
๐Ÿ› ๏ธ industrial hardware equipment: plastic furniture fencing pack logo

๐Ÿ› ๏ธ Industrial Hardware Equipment: Plastic Furniture Fencing Pack Review

3

ยท

Excellent

Revainrating 5 out of 5ย ย 
Ratingย 
5.0
โš™๏ธ Biscuits & Plugs, ๐Ÿ”ฉ Industrial Hardware

View on AmazonView on ะฏM

Media

(2)
img 1 attached to ๐Ÿ› ๏ธ Industrial Hardware Equipment: Plastic Furniture Fencing Pack
img 2 attached to ๐Ÿ› ๏ธ Industrial Hardware Equipment: Plastic Furniture Fencing Pack

Description of ๐Ÿ› ๏ธ Industrial Hardware Equipment: Plastic Furniture Fencing Pack

^^NOTE^^ The size listed 1-1/8" round is for Out Side Diameter. Its suitable only up to 1.05" TUBE inside HOLE diameter. If you need larger than 1.05" ID, please choose bigger the correct Out Side (OD) plugs. Please measure your Tube OD and ID before ordering and avoid returns. See the measurements in the title and bullet points to make sure they meet your needs. For Fencing Posts, Furniture End Caps, Fitness Equipment End Caps. Flexible ridges snugly hold these plugs in place. For Unthreaded Surface Type with Stright Profile. Wide Flexibility from 14 to 20 Gauge Tubing. 1 1/8" (14 - 20 Ga - 0.96"-1.05" ID). (Pack of 8) - 1 1/8" (14 - 20 Ga - 0.96"-1.05" ID) Round Black Plastic Tubing Plug, 1 1/8 Inch End Caps - Steel Furniture/Fencing Post Pipe Insert | End Caps for Fitness Equipment. This plug top cap measures 1-1/8" diameter. The inside Ridges enable it to be used on Pipes/Tubes with ID range from 0.96" to 1.05". Please check the ID requirements before placing order.

Reviews

Global ratings 3
  • 5
    3
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Fits like a glove Suitable for industrial equipment

I bought these caps for an old metal chair for a family's outdoor use. The chair had sentimental value, so I wanted to restore it. I powder coated it and wanted to cover the tubular frame end on the armrests. These caps fit perfectly with a hammer blow. They give the pipe ends a finished look. They prevent water from entering the chair frame so there will be no internal rust in the future. My son 3D printed a set of black chair legs. The photo shows one of the legs.

Pros
  • Great for a small home
Cons
  • Questionable purchase for the elderly

Revainrating 5 out of 5

PERFECT for vintage Kawasaki H1/KH500 frame tailpipes!

I needed hoses to replace worn out plugs that Kawasaki's mother thought were "no longer available". I tried them after careful measurement and they fit PERFECTLY. All you need is a small hammer with a plastic or rubber tip to hammer it into the back of the frame. Once you throw them in the hole, they will go live! I couldn't ask for more for this set of 8 heavy duty hard plastic plugs! Note. My inner diameter of the tube was about 23.44mm or .923" and the outer diameter was about 28.94mm orโ€ฆ

Pros
  • Best
Cons
  • Ugly packaging

Revainrating 5 out of 5

Fits perfectly in a 1 " hole

I've searched everywhere for something to cover the front legs of my wrought iron kitchen chair. I had just renovated the floors and didn't want to ruin them. I removed the debris and old plastic discs that were stuck inside. The back legs had a threaded hole for the back legs to screw in, and the front legs had a hole, but it wasn't meant for a screw. I bought these 1 1/8" round plastic pipe plugs and was so surprised they fit as the hole in the chair leg is exactly 1 inch. They fit well. Iโ€ฆ

Pros
  • Pretty packaging
Cons
  • Can't remember