PETG rod ABS Maker 1.75 mm, 1 kg, black Review

This is probably the cheapest PETG, and of excellent quality. I found a new favorite brand of plastic, I will continue to order (In the photo, the lower surface of the part is printed without supports. It looks much better in real life, unfortunately, the focus on the phone is broken - I had to take a picture from half a meter)

I like this plastic (I take it not for the first time from the manufacturer on other trading platforms). From - / + there is no vacuum bag (zip bag), there is dust / dirt (it is treated with a filter). In general, for such money (≈900) you can’t find a petzh.

Printed enough of these plastics. And unlike their orange color, this one has excellent printing characteristics. I print 230 nozzle + 70 table.

I used to take it all the time, now I took it, the thickness of the bar is different everywhere, from 1.5mm to 2mm, because of which the nozzle is constantly clogged or the printer cuts the bar with a clamp At the moment, 1.5kg is just thrown away . I will look for other options.

In general, for their money, very top-end plastic. I hope that ABSMaker will expand their assortment on the market. Different pros: Cheap Qualitative good coil Box quality Filament in a sealed bag with silica gel With its cons: A little dusty (solved by a filter that prints in 10 minutes) Still a bit damp, needs to be dried immediately. Or am I so lucky

The caking is bad. Before that, I took the green one, where the Delhi are obtained as a monolith, and the black, fragile inside, did not bake the layers. I did not like. You can print parts that do not require high strength.

I strongly do not recommend it, if such quality is typical, then each print turns into a tape measure, whether there is enough bar of normal thickness for printing or the bar will get stuck. And the longer the print, the more likely it is not enough. Two six o'clock details screwed up

I have already printed 3 coils of this plastic, I am happy as an elephant. This is my main filament and there is no point in changing it.

Prints out beautifully! The temperature should be between 230 and 250 degrees Celsius. I adjusted it to 240 degrees Celsius, and the flight should go as usual. If you have properly adjusted the distance that separates the nozzle and the table, then there won't be any issues with the product adhering to the table. There is no evidence of "snot" throughout the printing process. The temperature of the table was adjusted to be between 60 and 70 degrees Celsius. When printing particularly wide or…

Quite decent plastic would be if it were not for the size of the reel. The inner diameter is smaller than conventional ones and the width is larger.

before that I took plastic from syntec - the plastic was very terrible, I took this plastic, the printing is perfect, I didn’t even think that this PETG can print so well.

Prints great! The recommended temperature is 230-250 C°. I set it to 240 C ° - the flight is normal. If you have correctly set the gap between the nozzle and the table, then there will be no problems with sticking to the table. "Snot" during printing is not observed. The temperature of the table was set at 60-70 ° C. When printing very wide / long parts, the edges of the model come off, but I sin on the printer and my own hands - plastic has nothing to do with it. Several times I raised the…

The black reel ended before it could start, leaving only positive impressions, like the turquoise one. But the white coil turned out to be transitional. I started printing with white PETG, and finished with "invisible". This is of course a joke. Printing keeps stopping due to tangled filament. Unraveled, restarted printing, but again the transition to the "invisible" plastic. General impressions are positive. I will order more, with the hope that I was "lucky" with a white coil.

Excellent plastic, but refused to print on the stock hotend, which I just didn’t try, as a result, e3d v6 + direct bmg and everything is fine)

disgusting. The plastic is not the correct size. starts 1.75 after a couple of centimeters becomes 3mm and these waves every cm just ugly. BLACK DO NOT RECOMMEND Pros below: disgusting. The plastic is not the correct size. starts 1.75 after a couple of centimeters becomes 3mm and these waves every cm just ugly. BLACK DO NOT RECOMMEND Cons: disgusting. The plastic is not the correct size. starts 1.75 after a couple of centimeters becomes 3mm and these waves every cm just ugly. BLACK DO NOT…

Its pros: Normal plastic. The main thing is to choose the temperature of the nozzle and heat the table to 85 degrees. Print speed up to 50 mm per second no more. With its cons: Garbage on the filament itself. Put a filter in front of the extruder and the problem will be solved.

Pros below: Inexpensive. Prints out of the box (when dry) well. Packed in a sealed bag with a lock, there is silica gel. Prints 235, 75 as specified. The rod is straight. Cons: Sometimes it gets confused on the coil, although perhaps this is not related to winding, it is difficult to check for sure.

Under black plastic on the FlyingBear Ghost 5 printer, the optimal parameters are: nozzle - 245, table - 75 first layer, 65 - the rest.