💪 Enhance Performance and Durability with QTEATAK PCIe NVMe M.2 2280 SSD Heatsinks Cooler & Mounting Screws Screwdriver Kit Review

I lost my M.2 mounting screw so I bought it (screw-only kits are about the same as this heatsink kit!). gets a little warm and helps buffer the drive from the graphics card, which of course contributes to its own heat. The thermal pad sticks a bit to the drive after use, which I found when I moved the drive to my new motherboard (which came with its own heatsink). Just pull it off carefully and you're good to go. Residual oil can be removed with a cotton swab and isopropyl alcohol.

So you bought an SSD but you don't have a screw and therefore you have no choice but to buy a screw and this is one of the cheapest kits you can get Buy. Basically, you're paying $5 for a one-cent screw; although this is not the fault of the company selling this kit. This kit includes several screws, a screwdriver, a heat sink, and hinges. I wanted to give this set $3 because it's very poor quality, the heatsink is basically junk and I wouldn't recommend using it. The screwdriver is also very…

everything you need and more to install an SSD/NVMe card on your motherboard. fits for 2280 and if for some reason your motherboard didn't come with screws and gasket or you just lost them then this will be taken care of. The silicone rubber bands are a little flimsy to the touch, but they're more than up to the task when your car stalls.

These tiny screws are needed to secure an M.2 SSD or NVME SSD to the computer's motherboard, and the protruding standoffs are used to attach the device to the M. 2 connector to align. These parts are not included with most M.2 devices, but some motherboards have them pre-installed in a hole on the board as a courtesy. This didn't happen with my Asus motherboard. The correct height post (mine requires the larger of the two sizes provided) must first be screwed into a hole matching the M.2…

is just what you need to install an NVM memory card for your hard drive. The fan heater is a great idea. The radiator mounting method is a bit cheap. Not sure if it does any good, but the heatsink looks nice. Basically, a dumb screw is needed. Received, everything worked and arrived on time. I think the radiator was important when choosing from 3 or 4 suppliers. You won't have this screw in your tool kit and Samsung doesn't include it for some reason.

I was looking for a screw for my new M.2 NVMe drive. The motherboard (Asrock) in my pre-assembled Skytech had a roll-on nut on the motherboard but didn't include a screw to secure the end of the NVMe drive after installation. So I needed a screw and I wasn't going to get it right now. This kit was a great value and included two bolts (plus two nuts in case I needed to replace it) and a heatsink for my NVMe that didn't have a heatsink. This entire package is reasonably priced compared to other…

There are better radiators out there and you do NOT need a screw, but chances are! These screws are VERY easy to lose as they are so darn small. For the price that others will charge you for just one screw, these guys give you a whole kit and heatsink. Do your research, you probably really need a heatsink, I didn't know if I did it or not, I just put it on, but after doing the due diligence afterwards I'm convinced a heatsink is a good idea , especially in a laptop. My drivetrain idles around…

TL;DR: Great kit at a great price with a few minor issues for a small number of users. --- I bought this kit mainly because of the heatsink. I installed an M.2 drive and wasn't sure if I needed a stand or an M.2 screw (my M.2 slot is completely covered by my vertically mounted graphics card). As it turned out, my board already had a spacer and M.2 screw installed. I didn't expect that as my motherboard is very old (MSI X99S Gaming 7 bought in 2014). Although I didn't need any fasteners, it was…