Header banner
Revain logoHome Page
🔧 adjustable diameter aluminum cantilever replacement logo

🔧 Adjustable Diameter Aluminum Cantilever Replacement Review

7

·

Poor

Revainrating 3 out of 5  
Rating 
2.8
🛠️ Workholding, 🛠️ Industrial Power & Hand Tools

View on AmazonView on ЯM

Media

(1)
img 1 attached to 🔧 Adjustable Diameter Aluminum Cantilever Replacement

Description of 🔧 Adjustable Diameter Aluminum Cantilever Replacement

MATERIAL-Made from Aluminum alloy, Strong and reliable, Keep your lamp or microphone firmly on the table. DIY YOUR OWN LAMP- Anything you want it to stand on a table, can be clamped beside desk, tube diameter less than 12mm. NO TOOL REQUIRED- There is a cross at the end of the clip, so you can easily lock it firmly in the table with your hands. A thumb screw next to the hole, so even if the pipe is small, it can be firmly fastened. FIT FOR 2 INCHES THICKNESS BOARD-This C-clamp suit for less than 2 inches thickness board. PACKAGE INCLUDE- 1 x Cantilever Bracket Clamp.

Reviews

Global ratings 7
  • 5
    2
  • 4
    0
  • 3
    2
  • 2
    1
  • 1
    2

Type of review

Revainrating 2 out of 5

Hole smaller than advertised

Smaller than advertised and narrower the deeper you go. I had to file the hole and shaft of the item I'm using it on to make it fit. Many others say that a drill makes it bigger. The protective layer of foam that touches the countertop has also come loose. A little uncomfortable.

Pros
  • C-Clamps
Cons
  • High Price

Revainrating 5 out of 5

Exactly what I needed. Easily drillable for .5 " lamp base

This is a good, solid base. The base is not the .5" diameter required for many pop-up lamps, but is very easy to drill out . hole to fit these half inch light bulbs. An added bonus is a thumbscrew that allows you to hold the lamp in a specific position. Good value for money.

Pros
  • Tools and Household Items
Cons
  • Repair

Revainrating 3 out of 5

Hole 1/2 inch and less than 12mm are not the same.

Very well made but will not fit lamps with 1/2" plastic pins like those made circa 2000. I wanted to replace 2 of these, glad I tried that first Hole is very small Both pins are 13mm I drilled through but would rather just place the clamp on the table and lower the lamp into the socket.

Pros
  • Hand tool
Cons
  • Questionable purchase for the elderly

Revainrating 1 out of 5

It WILL NOT FIT 1/2 " lamp stem

I read all the reviews that said it doesn't fit the standard 1/2" lamp stem, they were right but I didn't seem to to have choice, since I needed such a device. I took out my handy drill bit and slightly enlarged the receiving hole. Now it works perfectly and you don't notice it. So if you have bits, a drill and 10 minutes, you can put them to work for you. Lamar in Bakersfield

Pros
  • Power & Hand Tools
Cons
  • Update Availability

Revainrating 5 out of 5

Exactly what I needed. Easily drilled out to accommodate a 0.5 " lamp base

This is a good solid foundation. the diameter needed for many pivoting lamps, but it is very easy to drill a hole to make these half-inch lamps fit. An added bonus is a thumbscrew that allows you to hold the lamp in a specific position. Good value for money.

Pros
  • MATERIAL - Made of aluminum alloy, strong and durable, keeps your lamp or microphone securely on your desk.
Cons
  • disappears

Revainrating 3 out of 5

Hole 1/2 inch and less than 12mm are not the same.

Very well made but will not fit lamps with 1/2" plastic pin like those made circa 2000. I was going to replace 2 of them. Glad I did first tried.the hole is very small.both pins are 13mm.i drilled through but would rather just place the clamp on the table and lower the lamp into the socket.

Pros
  • WHAT'S INCLUDED - 1 cantilever clamp for bracket
Cons
  • Unbelievable price

Revainrating 1 out of 5

It will NOT fit a 1/2 inch thick lamp post.

I've read all the reviews that said it wasn't made to the standard 1/2" inch pin on the lamp fit they were right but i didnt seem to have a choice as i needed this bracket.convenient to drill and easy to enlarge the receiving hole.now it works fine and you dont notice.so if you bits , a drill and 10 minutes you can make this work for you Lamar in Bakersfield

Pros
  • FITS 2" THICK BOARD. This C clamp fits boards less than 2" thick.
Cons
  • Crumpled packaging