Screen Protector Compatible Widescreen Desktop Review

After about an hour of frustration and using both of the screen protectors that came with it, I put one on. Without much time, patience, or preparation, you'll get a bubble-free installation. I don't think the manufacturer can improve anything. It's just too much surface area and too big a sheet to allow for a completely smooth application; it is not the same as putting a screen protector on a cell phone. Yes, I followed the instructions. Once I applied it definitely reduced the glare on my…

I bought this for my picture in a frame that reflected so much I couldn't enjoy it. I could see the overhead light like looking in a mirror. As you can see in the picture the light is still there but very subtle. So that really helped (although I didn't know anything about anti-reflective plexiglass [and as available] at the time until I searched for a larger size). I have to say the bubbling is insane. for this product. I went over and over again to work out as many bubbles as possible. And…

It looks like a poor quality product. I've installed screen protectors with no problems. The attached card is not enough to remove air bubbles (see attached photo). The comments here indicate that this is a product that appears to be successful. The manufacturer needs a better product, better instillation tools, or better instructions (yes, I followed the instructions as recommended). Too bad it's a bad product. I look at screens over 6 hours a day and could use a screen protector to reduce…

Hello. I buy this because my new PC has a glossy screen and lots of light reflections around the room. This job is perfect. The only thing I don't like is the inability to install 100% bubble free but almost 95% free (on the side I'm starting to install a product with bubbles). I will recommend a wet install for this only, for a free bubble install. However, this product is really good if you clean your PC screen to perfection and you have humid air environment because this plastic is not…

Good. I bought 2 packs for my computer at work because you can't buy just one with it. It's almost impossible to apply without bubbles, after the third puff I gave up and only left a few bubbles in there. What I couldn't stand was that the image on the computer was blurry, the words were blurry and boring. I work in a doctor's office all day looking at patient information, so after about 10 minutes I took it off and threw it away. What a waste.

My first purchase came without a screen protector. I went back and the seller sent me a replacement. This time came with no consumables for installation. So I made a setup with one rule. it was difficult to install. Half of the film installed correctly and the other half fails to remove the bubbles. but the worst thing (for me) is this. the picture blurs along with the film. No matter which half of the piece (with or without bubbles), the attached image was as sharp as possible. So I start…

Was difficult to install but every screen protector is like that. With a large surface, I couldn't apply it without getting dust lodged underneath. You can pop a lot of bubbles with the tools included in the kit, but bubbles with some dust underneath will not come out. completely away. Luckily, they're barely noticeable when the monitor is on, but obsessive people may not be able to handle them. I bought it mainly for the anti-glare and it's not that great. It's better than no film, but I think

This anti-glare screen protector did a great job eliminating glare and reflections on my desktop monitor (HP Pavilion All-in-One). It was pretty easy to install, but first you need to carefully clean the screen and stick the film carefully. There were a lot of air bubbles immediately after installation, but with careful persistence and using the included squeegee and credit card, I removed almost all of the bubbles. I was able to pull some out on the 2nd day after installation. The remaining…

This anti-reflective film does exactly what it promises. My screen was a mirror and now I can use the screen without getting tired of looking at myself. There are a few things to note: 1) This is a large area to cover and you probably shouldn't expect to be 100% dust free under the sheeting unless you are working in a sterile lab environment. 2) Work quickly when applying the film to minimize dust intrusion; It's a static film. I tried putting on the first film as instructed in the instructions