Header banner
Revain logoHome Page
๐Ÿ”ง yg 1 diameter monolayer with enhanced vibration resistance logo

๐Ÿ”ง YG 1 Diameter Monolayer with Enhanced Vibration Resistance Review

4

ยท

Very good

Revainrating 4 out of 5ย ย 
Ratingย 
4.0
๐Ÿ”ง Milling Accessories, ๐Ÿ”ช Cutting Tools

View on AmazonView on ะฏM

Media

(3)
img 1 attached to ๐Ÿ”ง YG 1 Diameter Monolayer with Enhanced Vibration Resistance
img 2 attached to ๐Ÿ”ง YG 1 Diameter Monolayer with Enhanced Vibration Resistance
img 3 attached to ๐Ÿ”ง YG 1 Diameter Monolayer with Enhanced Vibration Resistance

Description of ๐Ÿ”ง YG 1 Diameter Monolayer with Enhanced Vibration Resistance

Variable helix angles combined with unequal flute spacing reduces vibration, improves surface finish, and provides higher cutting capacity and material-removal rates compared to conventional end mills. Suitable for high-performance machining on alloy steel, cast iron, stainless steel, titanium, nickel-based alloys, and mยญost materials with a Rockwell hardness less than C40. Long-reach end mills have an extended shank for access to recessed areas of the workpiece. Aluminum titanium nitride (AlTiN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than TiN, TiAlN, and TiCN coatings. Carbide is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life.

Reviews

Global ratings 4
  • 5
    2
  • 4
    0
  • 3
    2
  • 2
    0
  • 1
    0

Type of review

Revainrating 3 out of 5

80% lower cutter than square cutter

So far this product is amazing. It was purchased to mill the trigger area into a block of aluminum. Works much better than a chisel to be used with a jig at a fraction of the cost.

Pros
  • Carbide is harder than HSS or cobalt steel, making it more wear resistant at high speeds and longer tool life.
Cons
  • I don't like anything about it, everything is fine

Revainrating 5 out of 5

Try and learn cutting tools

Excellent quality cutting attachment until three of the four teeth sheared off and the bit broke in half after about ten minutes of use. I would buy the racquet again, I hope it was just a defect in the racquet.

Pros
  • Aluminum Titanium Nitride (AlTiN) coating lubricates the end mill, provides high temperature stability and abrasion resistance at high cutting speeds, and offers better heat resistance than TiN, TiAlN and TiCN coatings
Cons
  • Ugly packaging

Revainrating 3 out of 5

80% undercut suitable for milling accessories

So far this product has been amazing. It was purchased to mill the trigger area into a block of aluminum. Works much better than a chisel to be used with a jig at a fraction of the cost.

Pros
  • Aluminum Titanium Nitride (AlTiN) coating lubricates the end mill for high temperature stability and abrasion resistance at high cutting speeds and offers better heat resistance than TiN, TiAlN and TiCN coatings
Cons
  • alt

Revainrating 5 out of 5

Good quality bit I think

Good quality bit Aluminum block. I suppose you'd have to steal a bit to really test this. The shaft is an inch longer than I wanted and the length of the cutting blades is 1/8 inch longer than I wanted, but it's as close as I've found to my Mesmo without giving up a single nut.

Pros
  • Variable helix combined with unequal flute spacing reduces vibration, improves surface finish and provides higher cutting performance and stock removal rates than traditional end mills
Cons
  • Drill pack