I decided to write only because of inadequate comments about the installation. 1. All new batches come with amd straight brackets. 2. This is not a marriage, it's a feature))) Korean Zalman engineers found that this improves the processor pressure. 3. Installation is quite simple to carry out as follows. a. Apply thermal paste to the processor. drop the cooler. b. tilt the cooler slightly towards one mount, so that the bolt gets the mount, turn it 1 turn. in. let go of the cooler, under…

I chose according to multiple reviews on different resources and not in vain. True, for the first time I put it on the wrong side (they don’t laugh, because I assembled the PC for the first time!), I had to remove it, the thermal paste spread a little, I put it back together a little and put the heatsink correctly. According to monitoring in the BIOS, the temperature of the processor is normal. Therefore - the thermal paste is excellent, the cooler does its job. Thank you Koreans for a…

It is not convenient to put on amd motherboards. There are 3 different sets of screws in the kit and none of them fit the back stiffness bar from the original motherboard, although it looks more confident in appearance. It’s also inconvenient to bait, especially when you already applied the paste with your fingers, you can’t bait it like with screwdrivers. But it was possible to make screws with a wide eye, for example. In general, the mounting system as a whole is not very good compared to…

The very thing for AMD. I advise. With its pros. 1. Plenty of tubes and good plate density. 2. Relatively quiet fan. 3. Build quality. Worth your money. At the time of purchase (2022) was not much cheaper. 4. AMD 8320, even under load and at 4 GHz, never got warmer than 60 C °. 5. If you have a processor with little heat dissipation, and the case is blown, then the fan can not be used. With its cons. 1. Inconvenient fastening, strongly bends the motherboard. 2. Due to the high density of the…

suitable for any processor, even overclocked. Has some pros Despite my laziness, I am writing a review - this cooler suits me so much. Let me explain why: 1. of course, cooling itself! it's just top notch. i5-4690k at stock frequencies, simple 25-30C, stress test - 50C, taking into account the simplest KPT8 thermal paste. in overclocking to 4.6 GHz, the temperature of the hottest core does not exceed 80C, which is also very worthy in itself (I sin on bad spreading, because the coldest core is…

Finally got to the computer to write a review about this device. I love the Zalman brand, as well as TT and CoolerMaster, but this cooler frankly disappointed. Stone 2550k overclocked to 4.5 MHz. 45 degrees. The graphics are natural for everything. Cooling is excellent. Everything would be fine . But I noticed a hum, like from a transformer, moreover, "stepped", the more the CPU is loaded, the stronger the hum and the transition of revolutions is very noticeable. Even the wife noticed in the…

I am very pleased with the purchase, I took it for 1090 - I think that this is an excellent price for this miracle. By the way, about fastening: in fact, everything is quite simple. The main thing is to carefully follow the instructions, without missing a single point (no initiative!). Has some pros Installed on i5 2550k (without overclocking) instead of the standard one. Peak temperature dropped from 70 to 56-58 (approx). I am completely satisfied, I used the standard thermal paste. Its cons:

Excellent cooling. Possibility of self-upgrading. Speed ​​controller. Good quality thermal paste included. The one who wrote that there is nothing to smear, everything was perfectly smeared with that small bag in which there was thermal paste, it has a sharp edge. In general, a normal installer always has a razor blade for these purposes. Cooler-must have, the price / quality is on top.

If you want to save your nerves, look for a model with bent bars, if you have AMD, I don’t know how it is installed on Intel, I haven’t tried it. Be sure to install the backplate from the kit, forget about the native one from your motherboard, there will be no pressure. I didn’t use the thermal paste that came with the kit, it resembles chewing gum in consistency, I applied it, I thought, I erased it, I used Cooler Master.

I bought this miracle yesterday, put it on AMD Phenom II x4 965 BE (did not drive the percentage) instead of box silence and calmness. I got into the case 180 mm calmly, about 1 cm remained. As for the temperatures on the box. cooler was idle 30-32 degrees. in loads: in games for about 2 hours and in the AIDA64 stress test for about 1 hour it reached 55 degrees. on this Zalman, completely different values ​​​​in idle time 25-27 degrees. in loads: games and stress test AIDA 64 did not rise above

Installation does not cause any particular difficulties, slowly, 30-40 minutes. They write that there is not enough thermal paste in the kit. More than enough for one application. Thermal paste must be smeared very much! thin layer. A thick layer impairs heat transfer. Installed on i5-2500k. Turnover set to 900, above is not very comfortable. At rest, the temperature is not higher than 32 degrees. At full load no higher than 47. When overclocked to 4600 MHz, the temperature under load is…

Before buying this unit, check if it will fit into your case. The paste that comes with the kit was more than enough. I can't say anything about noise. Which of the 5 fans is noisier is hard to say. There are no complaints about the quality, everything is quite cultural and nothing falls off. The plates are quite rigid when lightly pressed, they do not bend. Substitution summary. In normal mode, the temperature dropped to 20 degrees. When rendering video - more than 40 does not rise. I am…

moved from asus triton 70. stands on phenom x4 955. simple - 38, load - 53 I didn’t really get confused about the thermal paste, because the radiator warped during the installation process, because the fastening bolts did not reach the backplate thread. I had to press the mother and the mount by force, from this the clamp turned out to be 101%. Ah cools he of course obolditelno and very quietly.

The radiator is very high and large, you need to measure it very carefully before buying - it may not fit into the case or close the memory strips. Has some pros Cools well: Intel Core i5-4670 CPU @ 3.40GHz (no overclock) 32 degrees idle, no more than 52 degrees under continuous multi-day maximum load. With its cons. Difficult to install: For installation, you need to remove the motherboard and install the cooler on the removed board in order to tighten the fasteners from below, otherwise the…

I chose the cooler for a very long time. For I changed the platform from AM2 to S1155 and the main criterion was the height of the cooler. The case remained regular and, according to estimates above 160 mm, nothing would have fit there. After reading the reviews on the CNPS line, I chose the Zalman CNPS10X Performa. Prior to that, I installed case valves from Zalman in all sold computers - they really liked the low noise level. This SO was no exception. I put it on the motherboard for a long…

Basically, I am satisfied with the purchase, but this time Zalman disappointed me in terms of workmanship. For beginners, it will be difficult to install it. there is not even Russified documentation. Its pros: Even distribution of thermal paste, cools well. The radiator does not close the slots for memory modules (at least for me). Cons: Disgusting fasteners, I had to slightly bend it. it was impossible to tighten the bolts - they flew out, they didn’t even fly out, but they shot)) And the…

I put it on the i7 4790k, with a 100% load (3ds max render) and overclocking to 4400 using turbo boost, the temperature does not rise above 78. In idle time, at reduced speeds - 40. I have not tried to overclock manually yet. There is noise, but acceptable. Vidyukha with two propellers makes more noise. But with the installation had to tinker. A very uncomfortable mount, although it may be me, my hands are not straight.

Easy installation. Someone wrote that they blocked the memory slot - throw your underpayment in a landfill and take a normal one. Someone wrote - there was not enough thermal paste - your hands are really from the wrong place. Someone wrote - noisy - sorry, but you have hearing problems. Someone wrote - a difficult installation, I had to remove the motherboard - this is your initiative. Personally, I only had to remove the second wall in the system unit (which is very simple).

After reading tests and reviews, taking this cooler, I realized that the 120 mm valve would have to be changed. I didn’t wait for the roar of the airfield in my system unit, and repeat other people’s mistakes, and together with the cooler I immediately ordered 2 Arctic Cooling F12 PWM (blowing in and blowing out), I attached the whole thing effortlessly to Performa, the temperature is above 52 degrees Celsius at 800 rpm did not rise. And the valve that came directly with the Performa simply…

At rest, the temperature of the processor on the Boxed fan was 45 and worked quietly (DO NOT HEARD AT ALL - fan speed up to 2022), at 100% load - about 60-62 + speed up to 5000 and a terrible rumble - this was the reason for replacing Now at rest no more than 5 degrees above the room temperature at rpm up to 800, and at full load 42-45 at about 1000 rpm (didn’t regulate anything, just installed and launched). There is an opinion about the stability of work with the complete shutdown of coolers,