Header banner
Revain logoHome Page
🖊️ synthetic pen bushings - set of 12 non-stick white pen bushings for durable ca finishing and pen turning logo

🖊️ Synthetic Pen Bushings - Set of 12 Non-Stick White Pen Bushings for Durable CA Finishing and Pen Turning Review

3

·

Poor

Revainrating 2 out of 5  
Rating 
2.0
🎨 Drawing, 🎨 Painting, Drawing & Art Supplies

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🖊️ Synthetic Pen Bushings - Set of 12 Non-Stick White Pen Bushings for Durable CA Finishing and Pen Turning
img 2 attached to 🖊️ Synthetic Pen Bushings - Set of 12 Non-Stick White Pen Bushings for Durable CA Finishing and Pen Turning
img 3 attached to 🖊️ Synthetic Pen Bushings - Set of 12 Non-Stick White Pen Bushings for Durable CA Finishing and Pen Turning
img 4 attached to 🖊️ Synthetic Pen Bushings - Set of 12 Non-Stick White Pen Bushings for Durable CA Finishing and Pen Turning

Details

Ink ColorWhite
BrandZonon
MaterialHdpe

Description of 🖊️ Synthetic Pen Bushings - Set of 12 Non-Stick White Pen Bushings for Durable CA Finishing and Pen Turning

Make your finishing easier: you will receive sufficient quantity pen bushings in this package, with these pen bushings, your finishing will become more easier. Non-stick and reliable: these white pen bushings are made of HDPE material, which will not stick to your pen, it can save pen barrel and bushing, and also save your time to clean it. Appropriate size: these non-stick durable pen bushings are measure approx. 0.55 inch in width and 0.43 inch in height, pre-drilled for a standard 7 mm pen mandrel, 60 degrees cone-shaped taper suitable for most size pen bushings; Manual measurement, please allow slight errors on size. Save time and energy: these synthetic bushings allow you to access and finish the ends of your pieces easily unlike the flush steel bushings, which is time and energy saving. Practical to use: for anyone who does any sort of turning and likes to apply a CA finishing, these bushings are must have items on your work table, with this product there is no longer have the problem of accidentally gluing blank and bushings together.

Reviews

Global ratings 3
  • 5
    0
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    2

Type of review

Revainrating 1 out of 5

The diameter is too big.

The diameter is too large for the standard grip sleeve mandrel. This causes the workpiece to wobble (severely) as it rotates on the lathe, making coating very difficult, if not impossible.

Pros
  • SIZE TO FIT: These durable non-stick grip sleeves measure approximately 0.55" wide x 0.43" high, pre-drilled for a standard 7mm pen shaft, 60 degree taper, fits most pen sleeve sizes; Manual measurement, please allow a little error in size
Cons
  • old

Revainrating 1 out of 5

Too loose on the mandrel

It's a little oversized. In fact, they are so large that you can insert a 7mm brass grip tube and then slide them onto the mandrel. This is when you get what you pay for. Use them and your pen sleeves will most likely be off center. would not recommend

Pros
  • Save time and energy: Unlike steel flush bushings, these synthetic bushings allow you easy access and machining of the ends of parts, saving time and energy
Cons
  • Not bad, but...

Revainrating 4 out of 5

Too small ID

These sleeves are too small to fit on a regular pen holder. I used a 1/4" bit to increase the inside diameter a bit. Don't linger or the inside diameter will be too big. Pin to remove the pin core assembly. Ten of the twelve I received are tight now, but not tight Two is too loose for this purpose but still useful for CA trimming.

Pros
  • Non-stick and durable, these white pen sleeves made of HDPE material won't stick to your pen, saving pen body and sleeve and cleaning time
Cons
  • High price