I bought a cooler for my ficus 8350. I was just a little shocked by the temperatures, since before that I had stood at 100 watts and it was not enough for 125 watts. This one is so severe that I had to turn off the fan in idle PC mode, as the temperature drops to 10 degrees on the CPU I am very glad that I bought KrasnayaShapka, the temperature did not rise above 65 on full downloads in tests and games. for FX8350 I recommend cold percentage even in Turbo-boost mode.

I have been using since September 2022, everything is super. Temperatures dropped 4-5 degrees on the Ryzen 5 1600x overclocked compared to the Chinese cooler, which is one of the hottest rocks.

My system: asus z370-g gaming micro atx mother, Corsair Veng. RAM (55mm! high), 8700K processor and Aerocool P7-C0 case (175 max cooler height). This is the most important thing, I think. I thought I knew a lot about computers until I ran into the "Dimensions" problem. The height of the cooler fit with a margin of 5-8 mm, did not measure, there is a photo. There was a catastrophe along the length, the heatsink stood on top of the RAM, but the fan itself rested against it! Yes, it can be raised

I managed to screw the radiator with a regular screwdriver, holding it at an angle, and then screwing the screw to the end with pliers on the side. If someone cares, then there is no backlight. There is only one cooler included. Some pros: A huge piece of lattice metal. This can really remove about 250 watts of heat. It is possible to install an additional second cooler, but only one is included in the kit. Very reliable and convenient spring fastening: you can not be afraid that you will…

I took it before the New Year for 2300. On the Core I5-2500K at a frequency of 4.6 GHz, the temperature in the Aid stress test is 56 degrees maximum, for 4 hours of running, in games about 50, in idle 35 on average. I smeared it with thermal paste from the kit, installed it somewhere then in an hour. The main thing is to first fasten the radiator (with a long screwdriver), and then install the fan. A tutel-in-tutel fit into the Zalman Z9 plus case, so keep in mind. In general, I am satisfied…

The first installation may seem like a living hell, especially if there are large VRM zone radiators around on the motherboard, but you still need to crawl and snap this thing somehow. When using RAM with high radiators like Patriot Viper Steel, you will not only have to replace the standard 140mm fan with a 120mm one, but also move it higher, which will cause the height to be all 170mm. However, I used the complete 140mm turntable on the 1155 platform with DDR3 Kingston HyperX Fury with very…

Comparing with competitors' coolers, which are a bit more expensive (thermallight mostly), Redhat wins only in price. Absolutely ugly fastening of the cooler to the AM4 socket spoils the first impression. Is that how you treat your customers if you can't cut bushings to fix a dangling backplate? In general, there is trouble with the mount: poor downforce gives a weak cooling result. After a cunning modification of the mount (cut out the plastic bushings for the backplate, lowered the bracket)…

If you choose a tower for a long time and do not want to spend too much, then this is your choice, and buying slightly cheaper towers and much less efficient is not the best thing to do, anyway, then you most likely want to take a quieter and more efficient cooling, so it’s better to take it right away for a long time, the norms of cooling, so that later you can change the iron and not spend money on the tower \ every time.

Previously, there was a deepcool gammaxx s40, on the whole it was fine, but it was worth overclocking the percentage in stress tests, it doesn’t cope very well, it’s clear that there won’t be such loads in games, but if you don’t want to indulge in overclocking And I’m happy with the hat, I bought it more than three years ago, with fx6300 overclocked to 4.2 Ghz I coped with a bang. After a while, the cooler went through several systems, after the fx 6300 it was even hotter than the fx8350 125W…

Pros: Probably cools well! but not great! there is no special difference with a cooler 2 times less with 4 tubes from China! on 2600x processor Its cons: very thin, hyperx predator RAM doesn't fit, could have been shorter! In general, the choice of RAM depends on the cooler! this is not very convenient!

The budget version of the tower, the declared power output is 250 W, 135 W removes exactly, already the maximum speed and the temperature is about 75 at home more than 30, that is, in the summer, in the heat, with a video card and ssd, there is a cooler for blowing from the top of the case, though Different pros: Very affordable versatile tower. Cooled i7 6700k, took the same one for r9 3900x, keeps overclocking to 4000 MHz in summer, overclocked to 4200 MHz in winter, it could have been a…

First of all, think about whether it will fit into your case, I did not have a couple of cm and the lid does not close. You also need to be careful with RAM, because if you have it high, you will have to take it out (I have a distance between the radiator and the memory is less than 1 cm), the cooler is like a 4-pin one, but it always works for me at 100% (perhaps because of the old mother) At 100% speed, you can hear it, but if your headphones have at least some kind of sound insulation, then…

High, will not fit into any case. If you have memory with high heatsinks, be prepared to change the bundled 140mm cooler to 120mm (it fits great, install after installing the RAM on the board and mounting the heatsink on the processor)

An AMD Ryzen 5 2600 overclocked (ASUS Optimal preset, 3.85 GHz) runs at about 50 degrees with Firefox open with four YouTube tabs in the background. Without it, about 40 degrees. Very quiet. It is worth considering that for installation you will need a thin screwdriver with a length of at least 10 centimeters and a maximum diameter of a centimeter. With its pros: Very efficient cooler, can distribute up to 100 watts without a cooler and up to 250 watts with a cooler, good thermal paste…

Has some pros: For its price, almost a kilo of a good radiator. 10900f under load more than 73 did not rise (6 case coolers) Different cons: Well, he's healthy, yes. Well, you need a long screwdriver. But I went into the mix price and bought it for 100, not really a problem.

a good product, but you immediately need to take a long screwdriver, if not, because they don’t put it in the kit, but you can’t fix it in another way

I don’t know, the tdp is like 250 watts, but with a 105-watt ruzen it somehow copes with a creak (And as always, I like to read reviews where people put it on cold processors and put 5) As a result, I had to downvolt the CPU so that it would not warm up above 75 with this crap in stress tests dropped the voltage from 1.35v to 1.25v, and left the frequencies as they were, 4GHz as a result 64-66 degrees in the LinX stress test well anyway.

There is no backplate for AM4 in the kit! Be careful. Although the box has the inscriptions Ryzen, AM4. The instructions have a corresponding picture, but the backplate on it is hidden by the motherboard. For AM4, the backplate that is in the box is not suitable. And if you don’t have it, well, for example, it wasn’t included with the motherboard, then don’t put it on AM4. It was a surprise for me to get a cool expensive cooler that is impossible to supply. I bought my son a computer for…

Has pros: 1) Price 2) Dissipated power. You can set up to 10900k in overclocking. 3) connectors for any socket and processor 4) appearance 5) Quiet. You can't hear the fan at 900 rpm. Has cons: Perhaps one of the most inconvenient fasteners for the processor, in the absence of a long screwdriver, it is very difficult to get to the fastener screw.

Has some pros: A powerful thing that will make the processor freeze. My fx 8350 with heat release of 125, and even under overclocking, froze under this thing. And this despite the fact that it is not loud. With its cons: The smallness does not fit into the middle tower case, a little rests, which is why the cover (glass) at the top (where this cooler) does not fit tightly, I had to seal the crack with adhesive tape so as not to disturb the air circulation.