Fully Assembled CR-V Steel 8-Inch 3-Jaw Gear Puller For Easy Removal Of Gears, Pulleys, Bearings, And Flywheels - DURATECH Gear Puller Tool Review

This is a great product for the money. Other than the finishing and the quality of the metal (all of which could be better!) this works extremely well. I used this to pull off the flywheel of my lawnmower and it worked effortlessly. Recommmended!

I did not find this product durable. It had broke, or more clearly exploded. Always wear eye protection. I believe if you don't use everyday or under lots of pressure it's a good purchase.

It works and gets the job done. Its a hassle to get it to stay put but once you get it tight then it’s pretty easy from that point forward. For the price its a good deal.

I got this after trying a set of 3 from Harbor Freight. I prefer this one. It's good quality for the value. The other ones I actually threw away cause they were just so cheap feeling and flimsy and made them hard to use. I'll be purchasing another one of these ones in my near future. I used it to get bearing off jointer cutterhead and motor shaft. Had no issues

Seemed to work ok until starting to pull on bearing. The center stud threads just stripped while trying to break bearing loose.Update: Seller replaced unit & it works great! Must have been bad unit.

I wish the arms could be less floppy, that would make it easier to use. However, that’s not that big a deal and it does what it is supposed to do.

We bought this to work on our car and it was perfect. It looks exactly like the pictures, came in great condition, and works!Will update with a picture soon.

Learning to use this extractor/puller was very easy to work with. The three hooks are reversible for additional uses. The quality of steel is to be commended. The center threaded drive shaft appears to be fine high-carbon steel. When used with respect to it's capabilities, I would highly recommend the tool.

I got the 4 inch, big enough to pull this fan (from an AC condenser) off the motor. It was stuck pretty bad, I thought, but (after I sprayed some oil in it and let it sit) it came off just like that.If you don't know what these things do, this is what they do: the three claws pull (on the fan, the bearing, etc.), while the center threaded axle pushes (against the axle the fan etc. is on). You simply put the axle up against each other, maneuver the claws around the object you wish to remove, and

This gear puller is worth more than the price I paid for, and is built rather sturdy and engineered well! Thanks again DURATECH!LSS, Mililani, HI

Bought this gear puller to pull off a steering wheel adapter. It was very easy to use and I was able to pull the steering wheel adapter right off.

I like the quality of the products and the timely manner in which they were delivered to me. I used these products to fixed automotive HVAC.

Worked great for pulling harmonic balancer off my truck. Used it a few more times on other people's cars. If you know what it is and how to use it, should work fine for an exceptionally low cost

Had trouble removing the hubs on my jeep, so decided to buy this puller; this tool made life much so much easier. Had the hubs off in no time. Would definitely recommend.

Puller did not work with the bearing kit as advertised! Jaw ends were too thick to get behind the bearings so it was useless in my project. Good value otherwise for the price!

Bought this little puller to remove a stuck rear wiper arm from an SUV. worked perfectly and prevented damaging the wiper motor and glass as this allows you to put zero pulling pressure on the shaft. very handy tool to have around.

This product is not fully assembled as stated. No instructions on how to put it together. Thankfully not very hard to do so. Other than that, tool is fine.

Purchased these to remove the old (original) rusted & stuck rotors off of my 2001 F150 Supercrew 4x4. I tried using normal methods of persuasion - mallet, penetrating oil and even a sledgehammer and nothing worked. But this made simple work of these rotors.

Not something I will use or need very often as a D-I-Y person, but worked perfectly when I needed to remove a pulley from a woodworking tool in my shop.

Actually was used to free up seized axle inside hub bearing instead of as a hub puller. So somewhat opposite of intended use but it still worked well and served the purpose I had in mind when ordered. Certainly made the repair work I was doing much easier. Fair price and quality material. Delivered on time.