Pack Of 2 TMH 6 Inch Oval White LED Lights For Truck Trailer With Reverse Lamp, Turn Signal, Side Marker And Tail Functions - Surface Mount, Ideal For Trailers, Buses And Vehicles, 12V DC Review

The lights seem OK. That being said, the wires give me a not so great feeling about the durability. For starters, the black wire is ground, which for trailer lights is odd. Also, they are very thin, cheap tin wires. If they were some 18 gauge copper wires with a more durable shielding I would have been much happier. Only time will tell how well these work. I installed them on my boat trailer and I'm hoping they will work well in the wet environment. I do like how the wires are directly molded…

Revision. The Seller sent two new lights to replace the defective light.One light proved defective after 7 months. Exchanged 4 emails with the seller without being certain of any final results. I Felt it to be Unfortunate because it was a fine light when it was working right. Happy to be able to recommend this product and seller.

They use Non-standard wiring but it's not so bad.Black is ground. = Trailer side is White.White is bright, for signaling and braking. = Trailer side is yellow-left and green-right.Red is running lights, Half brightness marker tail lights. = Trailer side is brown, or sometimes also red.Careful not to gouge the delicate wiring, I thought I had enough clearance but gouged the white wire on tightening it down.They seem sturdy enough and bright enough so all is good so far!

I bought these lights as an add-on set of reverse lights for a small concession trailer. The lights have a 4-point screw-mount setup and will need about a 3/4" hole (basically an oval will do, parallel to the long axis of the unit) for the wiring to run through as the protective epoxy at the wire exit protrudes out too far for a true flush mount.This light has the standard dual-level output of a parking/taillight setup with a 3-wire connection. I'm only going to use the black (-) and white (+)…

Be sure to read the description for wiring. To save some trouble: black is ground, red is running lights, white is turn and stop. I went off of what I thought it should be, but hey, not every light is the same. Still a functioning tail light. Now to see how long it holds up on a boat trailer.

The light bulb burned out in one of my 2002 travel trailer tail lights. I had replaced the old bulb trailer lights on my boat trailer with an LED light for marine use and liked them so I thought I would try these on my travel trailer. I did have to drill some new holes and seal up the old holes but it seems to be worth it. The lights work fine and are much brighter than the old bulb lights.

Bought these to replace the lights on my travel trailer. I had issues with running lights and brake lights before and this resolved my issues. They were easy to install and work well for 4pin wiring setup with seperate brake/turn and running wiring.

Love these lights, I also love the fact that there is an option for a dim and bright setting with the wired, ( White and Black) bright and (Red and Black) dim. I would definitely buy again. Too bad they stop shipping to AK right ofter my order lol.

clear marking lights and turn signals, I LOVE IT. TMH ( Pack of 2 ) 6" 10 LED Surface Mount Oval Amber Turn Signal Side Marker Tail LED Light for Truck Trailer Trail Bus 12V DC

What a good surprise seeing the quality of this light assembly. I purchase these to have the ability of the side markers BLINKING right along with turn signal indicators. At night time, on each side of my trailer light up and blink in turns. What a way to visibly see the whole side of my trailer

Installed these as turn signals on the front of my Honda Pioneer 1000. Trimmed the plastic from around the lights, then used 3M double lock tape and attached to each side of the windscreen. They work great!

Mounted them on the bumper on my CJ 7 for some extra visibility . They worked perfect for a while , but now the little leds are starting to go out . It's hardly my daily driver , so less than 6 months of minimal use they are already failing

The wiring does not match up to American color codes. You will have to test the wiring before a final splice. The holes matchd up with the original trailer frame holes.Lights are bright.Have to see how long they last.The lamp was used on a submersable boat trailer. Lasted 15 months and the 40% of the LEDs stopped working.

Lights are just as advertised, good difference between running and brake lights, very bright. Flat across the back making an easy installation, just cut a hole for the wires. Doesn't come with wiring instructions, but the Best Buy site had it listed in the specs. (black is ground). Mounted to my cattle trailer, very pleased with the outcome. Will purchase again if I need to replace tail lights on any of my other trailers.

Well they didn't even make it a year before LEDs went bad. I honestly only ran them for maybe 20 minutes max. They are on a old jeep wagoneer project of mine that I been slowly putting together. They sat outdoor in the rain and sunshine. Which they are ment to be on trailers or trucks so they should of lasted way longer. Disappointed well now to find a better set.

These are very easy to install and look really good. Nice and low profile so we cant step on it and break them like the old square style.

Plastic is so brittle it broke when installing it, but I drilled new holes in different spots and mounted it just fine, the fit doesn’t allow them to mount perfectly smooth, but they worked great after figuring out the wire colors mean nothing. Trial and error until I got them working and now they are good.

Easy to wire up and mount. I needed replacement taillights for my 1953 Willys Jeep. These worked perfectly and have given me zero issues.

I added these to my utility trailer The original tail lights on the fenders are low and don’t show up that well, in my opinion. So I added these on the rear tailgate of my trailer. Wired them up the the existing tail lights and wow what a difference.

Amazing quality. BUT make sure you read the wiring diagram. The color coding isn’t the norm. That being said I buy these regularly as they are truly some of the best lights for the money.