Header banner
Revain logoHome Page
table inserts (set of 2) for 14-inch πŸͺš band saws or scroll saws (2.5-inch diameter, 0.1-inch thickness) logo

Table Inserts (Set of 2) for 14-Inch πŸͺš Band Saws or Scroll Saws (2.5-inch Diameter, 0.1-inch Thickness) Review

7

Β·

Very good

Revainrating 4.5 out of 5Β Β 
RatingΒ 
4.4
πŸ”© Power Tool Parts & Accessories, πŸ”§ Power & Hand Tools

View on AmazonView on Π―M

Media

(4)
img 1 attached to Table Inserts (Set of 2) for 14-Inch πŸͺš Band Saws or Scroll Saws (2.5-inch Diameter, 0.1-inch Thickness)
img 2 attached to Table Inserts (Set of 2) for 14-Inch πŸͺš Band Saws or Scroll Saws (2.5-inch Diameter, 0.1-inch Thickness)
img 3 attached to Table Inserts (Set of 2) for 14-Inch πŸͺš Band Saws or Scroll Saws (2.5-inch Diameter, 0.1-inch Thickness)
img 4 attached to Table Inserts (Set of 2) for 14-Inch πŸͺš Band Saws or Scroll Saws (2.5-inch Diameter, 0.1-inch Thickness)

Description of Table Inserts (Set of 2) for 14-Inch πŸͺš Band Saws or Scroll Saws (2.5-inch Diameter, 0.1-inch Thickness)

Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it. Make sure your insert recess has the locating pin on the side, not on the rear. use on 14" Band Saws and 24" Scroll Saws.2&1/2" X .100 thick Please measure your saws recess to ensure proper fit. They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports. IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.

Reviews

Global ratings 7
  • 5
    5
  • 4
    1
  • 3
    0
  • 2
    1
  • 1
    0

Type of review

Revainrating 4 out of 5

Fits Reliant Saw: Accessory

Of course you need to cut the saw blade, but you also need to make key cuts. Since they are plastic, this is easy to do. They fit well in the table opening.

Pros
  • Good product for the price
Cons
  • old

Revainrating 5 out of 5

Good replacement part

I bought these to replace worn out plastic originals for my Ridgid band saw. The fit was a bit tight but I suspect it was on purpose. Exactly what I was looking for. I would buy again.

Pros
  • Little competitors
Cons
  • Quality

Revainrating 5 out of 5

Works as it should

As the description says some will do, others need a little filing. I spent about 2 minutes with a file and shaved off the outer edge a bit. Fits well and works as it should

Pros
  • Comfortable to use
Cons
  • Slightly wrinkled

Revainrating 2 out of 5

Didn't originally fit

This item didn't fit (too big) on my regular 14" jet band saw. A trip to the belt sander to remove the paint from the edges and then the resulting burr from the surface solved the problem.

Pros
  • Stylish and modern design
Cons
  • Big and bulky

Revainrating 5 out of 5

Made for eternity. in Accessories for band saws

I really like these inserts. They are way better than the ones that came with the saw. The insert fits very snugly on the band saw table. The original insert that came with the saw was plastic and didn't hold up very well. This insert lasts a long time. I am very satisfied with the seller and the product.

Pros
  • Great price
Cons
  • Without machine

Revainrating 5 out of 5

Two for a good price

Arrived on time and undamaged. They are listed as unbranded 14" band saw inserts so I had to look at the picture and compare. They definitely fit the Ridgid brand and possibly other brands of 14 inch band saws. The paint is applied quite thickly so I had to use a file and sandpaper around the edges to help it slide into place. Very satisfied.

Pros
  • Sturdy construction
Cons
  • Boring packaging

Revainrating 5 out of 5

I bought these for my old model Harbor Load Saw, they worked great.

Perfect fit for my old model Harbor Freight saw. The only problem I have is color. It was thick enough around the edges that it had to be sanded down to fit the table notch hole. Make a trial fit before grinding. I would buy them again from this seller but I doubt I will need them. Those 2 inserts will likely survive the rest of the machine. I am very happy.

Pros
  • Very impressive
Cons
  • Some imperfections