Header banner
Revain logoHome Page
๐ŸŒŠ taidacent diy water level switch with relay: contactless liquid water level sensor for tank pipeline, with water level alarm (normally open, 12v relay) logo

๐ŸŒŠ Taidacent DIY Water Level Switch with Relay: Contactless Liquid Water Level Sensor for Tank Pipeline, with Water Level Alarm (Normally Open, 12V Relay) Review

3

ยท

Very good

Revainrating 5 out of 5ย ย 
Ratingย 
4.8
๐Ÿšจ Household Sensors & Alarms, ๐Ÿ”’ Safety & Security

View on AmazonView on ะฏM

Media

(4)
img 1 attached to ๐ŸŒŠ Taidacent DIY Water Level Switch with Relay: Contactless Liquid Water Level Sensor for Tank Pipeline, with Water Level Alarm (Normally Open, 12V Relay)
img 2 attached to ๐ŸŒŠ Taidacent DIY Water Level Switch with Relay: Contactless Liquid Water Level Sensor for Tank Pipeline, with Water Level Alarm (Normally Open, 12V Relay)
img 3 attached to ๐ŸŒŠ Taidacent DIY Water Level Switch with Relay: Contactless Liquid Water Level Sensor for Tank Pipeline, with Water Level Alarm (Normally Open, 12V Relay)
img 4 attached to ๐ŸŒŠ Taidacent DIY Water Level Switch with Relay: Contactless Liquid Water Level Sensor for Tank Pipeline, with Water Level Alarm (Normally Open, 12V Relay)

Description of ๐ŸŒŠ Taidacent DIY Water Level Switch with Relay: Contactless Liquid Water Level Sensor for Tank Pipeline, with Water Level Alarm (Normally Open, 12V Relay)

uses advanced signal processing technology and high-speed signal processing chip, which breaks through the influence of container wall thickness and realizes a true non-linear effect on the liquid level in the closed container Contact detection. The liquid level sensor (probe) is installed above and below the outer wall of the tested container (high and low level of the liquid level). The non-metallic container does not need to be perforated, is easy to install and does not affect production. It can detect the level of various toxic substances, strong acids, strong alkalis and various liquids in high-pressure closed containers. The liquid level sensor has no special requirements on the material of the liquid medium and the container, and can be widely used. Y28-NO / NC products are specially developed for non-metallic pipes (pipe outer diameter Dโ‰ฅ11MM) or level detection of flat containers.

Reviews

Global ratings 3
  • 5
    2
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Solid Pipeline Monitoring Solution

Based on my experience, this contactless liquid pipeline monitoring device is exactly what I needed to ensure constant safety and security in my home. It is incredibly easy to operate and even easier to install, making this purchase a no-brainer. I was pleasantly surprised by its accuracy and speed in detecting any abnormalities in the pipeline. The only downside I found was the higher cost compared to other similar products in the market. Nevertheless, I would highly recommend this product toโ€ฆ

Pros
  • Easy to use and accurate
Cons
  • Higher cost compared to competitors

Revainrating 5 out of 5

Works great as a fuel gauge on my golf cart

I hooked it up to the microcontroller and tied it to the side of my golf cart's gas tank. Works great for letting me know when the fuel level is low. Be sure to pay attention to the voltage requirements. This has 12V. I tried 24V first and couldn't get it to work with the microcontroller.

Pros
  • Tools and Housewares
Cons
  • Questionable purchase for the elderly

Revainrating 4 out of 5

works well well for security

I use it to shut off the water supply to my coffee maker. I glued it to the outside of the tank at the fill line. It is in series with the float switch which sometimes gets stuck. The solenoid and this sensor operate on 12 VDC. However, the 4 pin connector doesn't connect to anything I could find. I cut the wires and substituted another connector so I can disable the sensor if I need to remove the reservoir. If the connector was a regular connector or if there was a mating connector with wiresโ€ฆ

Pros
  • security
Cons
  • the list will be long.