TOPTOW 2-Inch Receiver Dual Hitch Extension - Extend Up To 10 Inches With 7.5 Inch Riser Review

You will NEED to buy "anti-rattle” hardware if you purchase this! It does not fit properly and it will sit very loosely in your hitch receiver.Anything you put into the receiver will also NOT FIT PROPERLY and will require tightening hardware to stop it from rattling and possibly FAIL- which could be catastrophic! I should have paid attention to prior reviews stating these same facts. This product is DEFECTIVE and I would NOT recommend purchasing it. IT IS NOT SAFE.

Worked perfectly for my 2021 Honda Pioneer 1000-5. I have a 7 x 12 atv trailer that I lifted to match the trucks hitch without a big drop hitch and a 4 x 8 trailer that I pull around the house for yard work. This dual receiver works perfectly for both trailers and is long enough that I didn't need the hitch extender I ordered to clear the exhaust. I am very happy with this product. It's just what I needed.

The part that a bolt screws into for stability bent and eventually tore off after lucening the bolt for the 3rd time total. I don't have faith that this will last and am surprised the warranty period is so short. I only bought this a couple months ago and I can't get product support. Honestly go to Lowes and pay a bit more for something that may last more than half a season.

The dimensions of the 2" receiver part that goes into your hitch is about a 1/16th of an inch too small. This causes excessive side-to-side and up-and-down movement. I welded a few pieces of steel to a side and the top to shim it to the correct dimension to achieve a proper fit.I like the unit overall, but wish it was properly sized from the factory.

The welds to hold the set screws broke right away i hope that is not a sign of the rest of the welds quality Thanks for attention.

Feel sorry if someone rear ends me at low speed. It’s very sturdy and provides a barrier my plastic rear bumper. Worked as expected.

No pin is included. Apparently you are supposed to understand that because the posting does not say that a pin is included that no pin is included.

The double receiver enables me to pull a trailer as well as hitch up a bike rack and carry bikes. However, the distance between the top and bottom receivers is too short to allow me to attach the trailer after the bike rack is installed. You have to attach the trailer first. So that means, you have to remove the bikes before you can remove the trailer, and that is problematic. The way I solved this problem is to add six inches between the receivers by cutting the pipe and welding additional…

The packaging was severely damaged in shipping. The packet with the Anti Rattle bolts tore open and one bolt was missing. The other bolt scratched up one side of the hitch. Even with those comments, the hitch is exactly what I needed! The structural integrity of the hitch is solid and I'm pleased with it.

We plan on using this on our RV, we haven’t had a chance to try it, but it’s very sturdy and it looks like it will serve its purpose!

Our Harbor Freight scooter wheelchair carrier was too high on our hitch to run our scooter on with the attached ramp without bottoming out. This adaptor lowered the carrier enough so the scooter runs up just fine. Very strong construction.

I should have heed the warning others have expressed. The outer diameter is too small and causes excessive play when installed in the receiver. I own others that provide a much better fit. I will need to weld in some shim material to get this one to not rattle/twist excessively. I would recommend trying another brand.

A renegade is a small jeep and you can't fit much inside so this dual receiver makes it easy to add extra racks & tow a trailer. I did buy hitch stablizer plates to keep the bike rack from wobbling as it's got a loose fit.

Made attaching cargo carrier much easier. Carrier was to close to rear bumper, hitch brought carrier higher and farther away from rear bumper. Also moved carrier out of the exhaust flow from vehicle.

This is one of those things that either works or it doesn't. It works.Also, I liked that they included two bolts that can be threaded in to lock in accessories without a hitch pin.

I use this on my RV. I am towing a car on th eloser and placing a bike rack on the upper. l It was a bit tought to install due to the openings being tight. Otherwise this is a well made, sturdy double hitch. I don't anticipate any problems.

This adapter works well. Some competing brands only tack-weld the parts together. This item was welded correctly, all the way around each joint. The extension for the accessory rack is placed high enough that there is no interference with the hitch when towing. Nice price, too.

The sturdiness and functionality of this is fine but the fit into a standard 2” receiver is incredibly sloppy. One would think that with all today’s technology, it wouldn’t be that hard to make a 2” hitch extender fit in a standard 2” receiver. There’s a solid 16th of an inch difference. The result: this thing wobbles all over the place. If you buy this, you’ll either need to shim it or be prepared for some serious play.

For Renegade owners that don’t have the $1200 bumper receiver, this is a life saver. Put a cheap, but low, receiver on and this raises it enough for bike racks, boxes etc. Good solid welds, and with a stabilizer doesn’t wiggle around too much.

Used this to elevate my cargo basket due to my hitch location being right next to the exhaust. It works great and feels super heavy. Hasn't rusted or anything yet