Header banner
Revain logoHome Page
1/2" hose barb beduan 3 way shut off brass y shaped ball valve - 2 switch control logo

1/2" Hose Barb Beduan 3 Way Shut Off Brass Y Shaped Ball Valve - 2 Switch Control Review

10

·

Average

·

$$
Revainrating 3 out of 5  
Rating 
3.2
🔧 Fittings, 🚰 Hydraulics, Pneumatics & Plumbing

View on AmazonView on ЯM

Media

(3)
img 1 attached to 1/2" Hose Barb Beduan 3 Way Shut Off Brass Y Shaped Ball Valve - 2 Switch Control
img 2 attached to 1/2" Hose Barb Beduan 3 Way Shut Off Brass Y Shaped Ball Valve - 2 Switch Control
img 3 attached to 1/2" Hose Barb Beduan 3 Way Shut Off Brass Y Shaped Ball Valve - 2 Switch Control

Photos by authors

(3)
img 4 attached to 1/2" Hose Barb Beduan 3 Way Shut Off Brass Y Shaped Ball Valve - 2 Switch Control
img 5 attached to 1/2" Hose Barb Beduan 3 Way Shut Off Brass Y Shaped Ball Valve - 2 Switch Control
img 6 attached to 1/2" Hose Barb Beduan 3 Way Shut Off Brass Y Shaped Ball Valve - 2 Switch Control

Details

MaterialBrass
Brandbeduan
Exterior FinishBrass
Inlet Connection TypeBarb
Outlet Connection TypeBarb
Number of Ports3
See 1 more

Reviews

Global ratings 10
  • 5
    4
  • 4
    2
  • 3
    0
  • 2
    0
  • 1
    4

Type of review

Revainrating 5 out of 5

Dual fuel for generator

Haven't gotten to use yet as I'm building my generator shed. I've gotten the Demand regulator (Nash Fuel) so I can use Propane or Natural Gas. This lets me choose which I want use. One for NG and the other for Propane>> Don't have no worries about cleaning a carb. with old gasoline jelled and dry in it! Just fire it up and back to normal. lol No Gasoline runs (waiting in line etc.), just open a valve, start generator and go watch TV. LOL,lol Pa ps: All things working- refer, TV, comp., etc.

Pros
  • Works well for my installation
Cons
  • May require frequent tightening to prevent leaks

Revainrating 4 out of 5

Works perfectly with some effort installing seals

Came quickly and with all parts. Seals are a bit fussy to get in. Really make sure it’s seated properly or you’ll have a leak. The inner small port of the seal needs to fit perfectly. One of the yellow plastic screw covers fell off and won’t easily snap back into place. It’s not a deal breaker though.

Pros
  • Came with clamps and thread tape. Worked perfectly!
Cons
  • Valve handle is very brittle and breaks easily.

I used valve to converge 2 drain lines, but the water was flow was not as expected. Turns out the knobs wear at the socket/valve interface and the built in 'stops' only make you think you changed the valve position. Pulling the cap and tightening made no difference. Very disappointed. Apparently there is no recourse for a refund at this point either.

Pros
  • Well made at a good price. Fast shipping.
Cons
  • Prone to leaks and drips

Revainrating 1 out of 5

Low quality materials. Broke within 3 months of use.

First one of the valve handles fell off, then I noticed leaking and the brass Y had actually cracked! All this after only 3 months of being installed. Leaked water everywhere. Is this really made out of brass?

Pros
  • It would be better if it had a way built in to mount to the boat that was solid.
Cons
  • Ggkiyfvml the motor be billed

Revainrating 4 out of 5

3/8 size does not completely fit a 3/8 fuel hose.

fit a 3/8 fuel hose. You can get about half way on to the barb. Spent some time on it to get it that far but with the clamps tightened down i don't think the line is coming off.

Pros
  • Used on my pontoon boat to tie in two gas tanks into the outboard motor. Works perfect.
Cons
  • Ggkiyfvml the motor be billed

Revainrating 5 out of 5

Works for me good for me

I put this on a small air compressor for my pond for aeration to bleed off the air if needed so I didn’t have to unclamped the hose. Works great

Pros
  • I used the valve for a permanent winterization point on a motorhome. Worked great.
Cons
  • Mine was wider than all my other 3/8" stuff that I used. I couldn't fit 3/8th tubing on it.

Revainrating 5 out of 5

First one was bad on my review.

The first one I ordered was bad and wouldn't shut off. They replaced it and the second one was ok but for some reason the handles are extremely wobbly but I think it's supposed to be. Its a good affordable part with very little other options to choose from. I also had to loctite the threads before use.

Pros
  • Just what I needed.
Cons
  • Limited durability compared to steel valves

Revainrating 1 out of 5

Garbage. 3weeks installed and falling apart

This is garbage. It’s been installed for about 3 weeks, ahead screws with holes valve handles in place are rusted and stained. One fell out, brass is very low quality pot metal and is stripping where the handle is screwed on. Don’t waste your time. This is typical Chinese crap.

Pros
  • I'm using this valve assembly to split an airline to pond aerators. Works well.
Cons
  • Can be heavy and cumbersome to handle

Revainrating 5 out of 5

Perfect for Testing Equipment

I'm in research and this little product was just one of those products you never know you really need. It was a the perfect part for the project I was working on and it really made my life easier. Thank you for making a simple but useful product, it's going to make so many people like me thankful that we get the job done and done right. Great product, great brand, and very cleanly manufactured.

Pros
  • Exactly what I was looking for!
Cons
  • Not suitable for outdoor use in all climates

Revainrating 1 out of 5

All the fittings leaked

All the fitting leaked, cheap hose clamps, one of the brass fittings was cracked and I lost a full bottle of welding gas because of all the leaks. Don’t waste your money.

Pros
  • perfect for what i needed it for, worked great
Cons
  • May not be able to withstand extreme temperatures