💻 Bosch 0232101024 OEM Camshaft Sensor for Audi & Volkswagen Models (1997-2006) Review

I usually try to buy original sensors but keep a few generic ones just in case. They work just like the original sensors, but you have to connect the original connector. DO NOT ATTEMPT TO SOLDER THE WIRES TOGETHER. The oxygen sensor wires are not made of copper. This is a special alloy that simply cannot be soldered. You must use the connector that came with the part or use heat shrink connectors. (assuming you have the correct crimping tool) https://www.youtube.com/watch?v=ex1Hki6-NHw This…

Not suitable for fittings on my 2003 BMW E46 325i M54 Sedan April 2003 model year THESE O2 SENSORS FOR THE 325I MANUFACTURED BEFORE AND BEFORE DATE 3/2003. I think there is a year classification for the 325i in 2003. Others like mine were made after that date and use other O2 sensors and other miscellaneous engine parts I found out. For BMWs built after March 3rd you will need Bosch 15680 and 15681 downstreams (both will fit both downstreams). And for upstream you need Bosch 17215 and 17216…

If you're having trouble starting, poor acceleration, rough idle, black smoke from the exhaust, or just a dreaded P0193 code, it's most likely a fuel rail pressure sensor. dies and wants to be replaced with a new working sensor. If the computer cannot determine the fuel pressure at the injectors, be prepared for a lean mixture in your combustion. In my condition, the Ford F-150 was running very rich with an incorrect reading of 11psi on the fuel rail. (hydrocarbon quickly filled the air and my…

Bosch makes good parts so when I saw this unit I didn't hesitate to buy it. When I received my part today, it was installed in just a few minutes. I spent a little more time unplugging the power connector from the old part so as not to damage it. You need to place a small flathead screwdriver on top of the latch and push it down, then gently pry it off the connector. I also stuffed it with paper towels before removing it from the engine and I only opened it slightly until the pressure was…

If you have a Mercedes S Class (2000-2006) then it's a must. You should always have a spare part in the car because these things sometimes break without notice or with very little warning. This little Crankshaft Position Sensor (CPS) will leave you calm and dry in a deserted parking lot after watching a movie and having dinner on your first date. You proudly walk to your hundred thousand dollar car, turn the key and all you hear is, uh, uh, uh, uh, uh, noise. You know, the kind that makes you…

This gauge fixed my 2004 3.2L V6 Crossfire starting problem! I am 43 years old and this part was very easy to install myself. My problems started after I drove into town one day. When I tried to start the car to get home, it kept overturning but wouldn't start. I waited a few minutes and thankfully it started up again. When I got home I parked the car and tried to start it and again it kept turning but wouldn't start. The next morning when the engine was cold it started right away, but after…

Update: took 5 months - went back to Denso V6 has three sensors: two before the catalytic one and this one after). First, Toyota is very sensitive to its sensors, which is why many people choose the Denso brand used by Toyota. That said, Denso sensors are at least twice the price, but they turn off the check engine light and last over 100,000 miles, which probably means a one-time replacement for most vehicles. Так что, если вы не пойдете по пути Denso, лучше всего подойдет Bosch, и, честно…

I bought a used car with no paperwork so I had no idea when they were replaced. My car hasn't given me any problems or codes, but as a preventative maintenance I decided to replace them. It was pretty easy, but it took a long time. The reason for this is that I used a crow's foot (22mm) instead of an O2 sensor socket. If you decide to buy an O2 sensor socket, make sure it is thick as the socket can bend if the O2 sensor is stuck very hard. The O2 sensor is located on the passenger side of the…

My 05 S430 didn't start the first time after a short stop. I ordered this part and installed it myself. 2 weeks and so far so good! The original part shows the BENZ and BOSCH part numbers, while this part shows only the BOSCH part number. Here are the rough removal steps after watching some good videos of yours. Pipe: 1. No need to remove the heat shield, just bend or push it down to give you more room to work with the E8 torx screw. I didn't do this when unscrewing the bolt, it was difficult…

Update: Lasted 5 months - back to Denso Bought for a 2000 Toyota Camry V6 as a BOTTOM FLOW sensor (after catalytic converter - furthest back sensor as the V6 has three sensors: two in front of the catalytic converter and one after). First, Toyota is very sensitive to its sensors, which is why many people choose the Denso brand used by Toyota. That said, Denso sensors are at least twice the price, but they turn off the check engine light and last over 100,000 miles, which probably means a…

The car was bought without papers so I had no idea when they were replaced. My car hasn't given me any problems or codes, but as a preventative maintenance I decided to replace them. It was pretty easy, but it took a long time. The reason for this is that I used a crow's foot (22mm) instead of an O2 sensor socket. If you decide to buy an O2 sensor socket, make sure it is thick as the socket can bend if the O2 sensor is stuck very hard. The O2 sensor is located on the passenger side of the car…

My 05 S430 didn't start the first time after a short stop. I ordered this part and installed it myself. 2 weeks and so far so good! The original part shows the BENZ and BOSCH part numbers, while this part shows only the BOSCH part number. Here are the rough removal steps after watching some good videos of yours. Pipe: 1. No need to remove the heat shield, just bend or push it down to give you more room to work with the E8 torx screw. I didn't do this when unscrewing the bolt, it was difficult…