Header banner
Revain logoHome Page
📸 gdstime 2-pack 50mm x 15mm blower fan 12v 5015 dual ball bearing dc brushless cooling turbo fan with 2 pin 39 inch cable for 3d printer accessory logo

📸 GDSTIME 2-Pack 50mm x 15mm Blower Fan 12V 5015 Dual Ball Bearing DC Brushless Cooling Turbo Fan with 2 Pin 39 inch Cable for 3D Printer Accessory Review

5

·

Average

Revainrating 4 out of 5  
Rating 
3.8
🧰 Computer Internal Components, 💻 Computer Components

View on AmazonView on ЯM

Media

(4)
img 1 attached to 📸 GDSTIME 2-Pack 50mm x 15mm Blower Fan 12V 5015 Dual Ball Bearing DC Brushless Cooling Turbo Fan with 2 Pin 39 inch Cable for 3D Printer Accessory
img 2 attached to 📸 GDSTIME 2-Pack 50mm x 15mm Blower Fan 12V 5015 Dual Ball Bearing DC Brushless Cooling Turbo Fan with 2 Pin 39 inch Cable for 3D Printer Accessory
img 3 attached to 📸 GDSTIME 2-Pack 50mm x 15mm Blower Fan 12V 5015 Dual Ball Bearing DC Brushless Cooling Turbo Fan with 2 Pin 39 inch Cable for 3D Printer Accessory
img 4 attached to 📸 GDSTIME 2-Pack 50mm x 15mm Blower Fan 12V 5015 Dual Ball Bearing DC Brushless Cooling Turbo Fan with 2 Pin 39 inch Cable for 3D Printer Accessory

Details

Item Dimensions LxWxH1.97 x 1.97 x 0.59 inches
BrandGDSTIME
Power Connector Type2-Pin
Voltage12 Volts (DC)
Wattage1.5 watts
Cooling MethodAir
See 5 more

Description of 📸 GDSTIME 2-Pack 50mm x 15mm Blower Fan 12V 5015 Dual Ball Bearing DC Brushless Cooling Turbo Fan with 2 Pin 39 inch Cable for 3D Printer Accessory

【WIDELY USED】50mm brushless dc blower fan; used in 3D printers, humidifier, humidor, aromatherapy, heaters, small PC and other small appliances series repair replacement. 【ENOUGH LONG】 3.28ft (100cm) 2-wire terminated with XH2.54-2Pin connector for power supply; meet connection needs (Red wire : positve, Black: negative). 【HIGH SPEED】 Dual-ball bearings have a lifespan of 67,000 hours and allows the fans to be laid flat or stand upright; Noise Level: 38.7 dBA. 【EASY TO INSTALL】 Blower Size: 50mm L x 50mm W x15mm H, Air Intake Size: 32.5mm, Air Outlet Size: 19.5x15mm, Mounting Spacing : 2.24 in; Operating Voltage Range: 7 to 13.5V. 【5015 BLOWER】Rated Voltage: 12V DC | Current: 0.1Amp | Power: 1.5 Watt | Airflow: 5.36 CFM | Static Pressure: 1.21 In H2O | Fan Speed: 6000RPM

Reviews

Global ratings 5
  • 5
    2
  • 4
    1
  • 3
    1
  • 2
    1
  • 1
    0

Type of review

Revainrating 5 out of 5

That does not work. suitable for computers and accessories

I only had time to test one of the two fans, but the first one doesn't work. I had to make sure my fan settings were on and they are actually on. They initially had a bit of movement but after about a week they stopped spinning fully but definitely not close to speed for cooling anything, I could barely feel the fan blowing. I will update the review when the 2nd fan works as expected.

Pros
  • LONG ENOUGH
Cons
  • I don't like it, everything is fine

Revainrating 3 out of 5

Powerful little fan

Incredible air from this tiny fan. I was very impressed. It's not very quiet, but it's very quiet considering how much air it expels. Versatile in use, therefore easy to connect. Would definitely buy again. A+

Pros
  • EASY TO INSTALL
Cons
  • Almost everything is fine

Revainrating 4 out of 5

Greta performance priced at

Purchased to add cooling and air delivery to a diode laser engraver. I needed to be able to control the directional flow into the shroud, so the fan design was better than a traditional axial fan. The fans are quiet and move air properly. Very quiet considering the airflow, so I'm quite happy with the whole setup. If I had to be picky, I'd like them to be in left and right handed versions, but that's just for aesthetic reasons. The description included detailed specifications and helped a lot…

Pros
  • WIDELY USED
Cons
  • Frequency

Revainrating 2 out of 5

Not the quietest fans in this class, but good performers.

I've had quieter fans of this size, but they cool well and are cheap. I haven't had a bad relationship with them and they go well with my 3D printer's cooling system. The cables are very long (probably too long so you'll need to tie them together) so there shouldn't be any issues connecting them.

Pros
  • HIGH SPEED
Cons
  • Little things

Revainrating 5 out of 5

A good fan, a bad fan.

The first fan I connected made a strange high frequency noise. How the spool howls. It went away on its own as I increased the RPM. However, the second fan suffers from the same problem that does not go away. Airflow is generally good. Definitely a hit or miss with questionable quality.

Pros
  • 5015 FAN
Cons
  • Some cons