Header banner
Revain logoHome Page
πŸ”Œ 12v reversing wired amp by industec logo

πŸ”Œ 12V Reversing Wired AMP by IndusTec Review

3

Β·

Average

Revainrating 3.5 out of 5Β Β 
RatingΒ 
3.3
πŸ”Œ Electrical Controls & Indicators, πŸ’‘ Industrial Electrical

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ”Œ 12V Reversing Wired AMP by IndusTec
img 2 attached to πŸ”Œ 12V Reversing Wired AMP by IndusTec
img 3 attached to πŸ”Œ 12V Reversing Wired AMP by IndusTec
img 4 attached to πŸ”Œ 12V Reversing Wired AMP by IndusTec

Description of πŸ”Œ 12V Reversing Wired AMP by IndusTec

#12 wires with female .250 plugs crimped and installed. Hole size is 7/8" X 1-1/16" or 22mm X 27mm. 16 Amps at 250V AC and 20 Amps at 125V AC. 20 Amps at 12V DC and 10 Amp at 24V DC. 6 Pins. Three positions. Excellent quality and an easy simple installation. A switch is an electrical component which can make or break an electrical circuit. A rocker switch is a type of electrical device that is actuated by pushing a button back and forth to open or close an electric circuit. Not Waterproof. Make sure you're using a switch and wire sufficient enough to handle the power that you are carrying. In higher draw applications, a relay may be needed. Always use a fast blow fuse for your rated amperage. Use terminals of good enough grade and quality to handle the amperage in the switch to avoid heat and damage. This polarity reversal switch is suitable for all kinds or electrical equipment, motorhomes, and power wheel quad. Its main function is to upgrade your equipment to reverse direction. Great Replacement parts for all sorts of DC motor reversing applications such as Camper Trailer Jack, RV Controls, in and out operation, open and close for doors, up and down for windows and liftgates. Also good to slide awning. Can be used for accessories on most vehicle. Momentary / Mom / Resetting / Springing / Temporary switch is used for jogging operations such as lift, hoist, winch, door, or window resets automatically (returns to center off position) when released. Forward Reverse Switch. Double Pole Double Throw, DPDT, 2PDT, DP2T, 2P2T, Dual Position, dual throw. This type of switch can be a little confusing. It might be easier to consider it to be two SPDT switches in one. They connect two different power sources to two different loads or accessories at the same time. It routes two separate circuits, connecting each of two inputs to one of two outputs. The position of the switch determines the number of ways in which each of the two contacts can be routed. Our Heavy Duty rocker switches are used in Car, Car Accessories, Race Car, Racing Needs, Truck, Boat, Airplane, Aviation, Motorcycle, ATV, UTV, RV, Camper, Trailer, Automotive, Marine, Industrial, Winch, Actuator, Liftgate, fifth wheel jack, Manufacturing, Bilge Pump, Auxiliary Cooling Fan, Solar, Light Bars, Sounds Systems, MRO Maintenance Repair, Appliances, Outdoor Lights, Dash Lights, headlights, Dome Lights, Engineering, Off Road, Design, Robotics, Automation, Tilt, Trim, DIY, Etc.
Hide

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    1
  • 2
    1
  • 1
    0

Type of review

Revainrating 3 out of 5

Crimp bad best in industrial electronics

As far as I can tell this is a good switch. But compression is bad. Three wires pulled effortlessly from the terminal. I have a box of terminals and a good crimping tool so I could do it well. But I shouldn't have done it. Only buy this switch if you have a crimping tool and extra terminals.

Pros
  • controls and indicators
Cons
  • damaged

Revainrating 2 out of 5

Good switch with bad wiring

I thought it would save wiring effort but I need to fix bad crimp quality. I saw a few strands sticking out and gave the wire a light tug. All the wire came out effortlessly. I need to go through and make sure all connections are secure so I can have confidence that this switch will work as advertised. Better quality control is definitely needed!

Pros
  • Industrial switch
Cons
  • disappears

Revainrating 5 out of 5

Preinstalled and works great!

This snap-action switch is pre-wired. Works great as a window switch. It wasn't hard to figure out because I had already rewired a 6-pin switch from scratch for another window. With that, the 6-pin main wiring was done, so all you have to do is connect the power and ground wires, then connect the 2 blue wires to the electric motor. The last momentary switch I bought was unplugged. Last time I had to use my own cables and plugs and it took a while. I had to find a wiring diagram and hook it up…

Pros
  • Industrial & Scientific
Cons
  • No Instructions