Header banner
Revain logoHome Page
πŸ“ high-quality meters white teflon bowden filament for optimal printing performance logo

πŸ“ High-Quality Meters White Teflon Bowden Filament for Optimal Printing Performance Review

3

Β·

Terrible

Revainrating 1 out of 5Β Β 
RatingΒ 
1.0
πŸ–¨οΈ 3D Printer Parts & Accessories, 🏭 Additive Manufacturing Products

View on AmazonView on Π―M

Media

(2)
img 1 attached to πŸ“ High-Quality Meters White Teflon Bowden Filament for Optimal Printing Performance
img 2 attached to πŸ“ High-Quality Meters White Teflon Bowden Filament for Optimal Printing Performance

Description of πŸ“ High-Quality Meters White Teflon Bowden Filament for Optimal Printing Performance

IMPROVE PRINTS: Regular Bowden tube cleaning can cause wear, and extruder grinding reduces print quality. Replace your filament tubing to enhance print quality. LOW FRICTION: Made from high quality, durable PTFE, the Teflon Bowden tube allows filament to slide better for smoother results. HIGH SPEC: Withstanding temperatures up to 260C, this Bowden connector tubing has a density of 2.15-2.20g/cm3, with a 2mm ID and 4mm OD. FLEXIBLE TUBING: PTFE Bowden tubes offer impressive flexibility – ideal for smoothly tracking the moving 3D printer head. Packaged without ties to prevent crimping. AMX3D ACCESSORIES: The best 3D Prints start with the best tools! AMX3d provides 3D printing partsof the highest quality. If there are any problems with your Bowden Tube just let us know!.

Reviews

Global ratings 3
  • 5
    0
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    3

Type of review

Revainrating 1 out of 5

OD too large and ID not centered

Waste of time and money. The OD of this tube is between 4.09 and 4.12mm for the length of the section I received. As with other reviewers, the ID was not centered along the entire length of the tube. I suspect people either get lucky with this, don't notice it, or don't have very tight tolerances for their thermal breaks. It goes in the bin and now I have a hot end that I can't use until I find more pipes as I crippled the old pipe when I took it out. The only part that was ok was that the…

Pros
  • Additive Manufacturing Products
Cons
  • thin

Revainrating 1 out of 5

can't push stuffing through

I was glad to get the hose as mine was pretty gnawed by the fittings holding it in the hot end and I'm afraid it will break and get stuck soon though when I put this tube on, I couldn't get the thread in as easily as usual. Eventually I wiggled it and pushed harder and it kept slipping and I realized I had threaded it, it was just so tight it wouldn't come off. It was a brand new ending, not an ending I cut off or anything. I then tried to carefully cut the end off with a razor to see if it…

Pros
  • Industrial & Scientific
Cons
  • Not sure

Revainrating 1 out of 5

The hose is fine, but make sure that there are no deformations preventing the thread from passing through.

Unfortunately, most of those PTFE tubes have been good. There was warp on 1/3 of a long piece of tubing I cut for my Delta printer. Luckily I bought this length as I was planning on saving just over half for future projects so I was able to get a good chunk out of that half for immediate use. Just make sure you cut every length of thread that can actually go through your pipe without getting stuck. It's easier to figure this out before you install it and wrap all your cables around the pipe…

Pros
  • 3D Printer Parts and Accessories
Cons
  • No Automatic