NEXT BY DANCO All-in-One Toilet Installation Kit: Perfect Seal Wax Ring, Zero Cut Bolts, and Reliable Toilet Repair - Wax-Free Solution for Mounting Toilet Bolts (10879X) in Blue Review

Great kit - dominates wax. Goes down 1-1/2 inches. My double wax was too short - barely touched the toilet. I'm surprised the old one worked at all. My closet flange is 1/2" below the tile. The toilet must have been moved after a few months and was leaking. This set fits 1-1/2" UNDER the finished floor. I also received the Korky and Fluidmaster waxless or waxless sets and sent them back - they only fit up to 1/4" or 3/8" under the tile or you'll have to double them. This kit can also be used to

I bought this product because it seemed easy to use and had a built in wax ring. My toilet flange is above the tile so try it on according to the instructions and if the toilet wobbles remove the inner black part. The toilet rocked so I took it off as instructed. He squeezed the seal as hard as he could, but the toilet still wouldn't flush. Removed the device and cleaned the wax, installed the toilet as a test without seals and it sat like a rock in the surf. I believe the flange of the unit…

This was my first time installing a new toilet (thanks Covid!) and thought this would be a great and reliable way to do it. NOT CORRECT. My flange is about 1/4" to 3/8" above the finished floor, so I installed it without the blue spacer. He rocked. I disassembled it and took out the black plastic ring. He rocked. I squeezed him a little more. Although in theory I was grateful that I could take it off and put it back on a few times without worrying about the seal leaking - once I took it out…

A toilet like the American Standard Cadet 3 only allows 1/4 inch off the floor (I didn't measure this before taking off my old toilet, ASC3 box opened and installed on Danco). The Danco 10879X All-in-One Mounting Kit increases flange height by at least 1/4" to 1/2". As a result, the ASC3 leans significantly forward. return. Edit 20180921: This was my first toilet installation. My floor is level and the 1/4" flange above the floor is in good condition. The ASC3 allows the flange to be raised…

A dream come true. As a young child, I never thought I would have the opportunity to review a toilet installation kit. But the time has come. I can not believe that! Works as it should. Take your time and follow the instructions and he will do what he needs to do. Ignore the instructions and you'll probably be in trouble I guess, like most of the one star reviewers here. Great design with "zero thread bolt" and removable top blue ring. Alignment pins are a brilliant idea. After redoing the…

I don't usually look at toilet mounting screws. But after using these amazing toilet screws I was so impressed I couldn't help but share it. I've replaced/repaired more toilets than I would like, but one of the things I've always hated are the mounting screws. Tightening hurts, cutting off the remaining screw (of which there are usually a lot) hurts. Even the small plastic washer that attaches the standard screw to the toilet flange doesn't work as well, making the toilet installation a little…

I wasn't sure if they would work when I first ordered them. I installed a new American Standard Champion toilet with long hold down screws and tall screw covers. The DANCO toilet pinch bolts were made of brass and stainless steel, so I was drawn to the ability of these metals to resist rusting. Toilet flanges can be high or low depending on plumbing and plumbing conditions. I had a low profile Oatey flange over a new porcelain stoneware floor. There was enough room in the stainless steel flange

Reinstalling a 30 year old toilet on a tiled floor so that the flange is 1/2 inch below floor level. The directions looked good, but along the way I realized they weren't up to standard. Luckily this wasn't my first toilet installation job so I knew what was going to happen. The first problem was the brass T-nuts. At first they didn't seem to fit my flange. But then I saw that the threaded parts on each nut were turned off on both sides. However, they weren't sharpened on the right sides. If I…