After doing some research online and reading some reviews, I came to the conclusion that the 120 mm valve on this cooler has to be replaced. I didn't wait for the roar of the airfield in my system unit, and I repeated the mistakes of other people. Along with the cooler, I immediately ordered 2 Arctic Cooling F12 PWM fans (blowing in and blowing out), I attached the whole thing easily to Performa, and the temperature did not increase to more than 52 degrees Celsius at 800 revolutions per minute.

migrated from an Intel Core 2 Duo E6400 to an Intel Core i7-4770K Haswell on the new system. Because of this, the previous one froze up when I increased the clock speed by 30%; nonetheless, it was easy to avoid turning on the cooler. The new Intel Core i7-4770K reached a temperature of 70 degrees Fahrenheit during the stress test when its clock speed was increased to 4.5MHz in the AIDA64 software. idling 28 degrees indoors 22-23 degrees. I got lucky with the processor; it turned out to be…

The deficiencies of the kit became immediately apparent while beginning the installation of the fan on the motherboard. Because the holes in the plastic "clamps" are smaller than the holes in the "nuts," the "clamps" need to be adjusted in order for the installation to go according to the instructions. After disassembling the native "socket" and attaching the assembled bar from the kit to the reverse side, I noticed that the middle part under the processor rests against the motherboard, and the

The fact that it could be purchased for a sum that was lower than 900 at one point contributed to the item's rise to prominence. The lifespan of thermal paste ranges from one to two years; thus, you must remember to renew it. Both the Cooler Master O4-P2B-12AK-GP (which you will have to modify a little with a hacksaw) and the Noctua NF-S12A PWM are inaudible up to 800 rpm while providing adequate cooling; however, the stock cooler is too loud. If you want a quieter system, you can replace it…

I got it and put it in yesterday; the installation took a considerable amount of time. It took probably more than an hour, considering that the entire computer had to be analyzed and collected. Although the paws that press the cooler down into the bottom plate are depicted as being bent in the instructions, in practice they are even and flex in a spring-like manner. And in a challenging manner. It is tough to put on the screws, and it is fearful that something would burst, but the board did not

The most significant drawback of this cooler, which possibly eclipses all of its advantages and disadvantages, is that it has a HORRIBLE INSTALLATION. To install, you will need at least three hands. This requires the participation of two different people. The bolts are not able to be inserted into the slots. Only after the second person on the opposite side of the motherboard pushes through the fasteners can the bolts be pulled and tightened. You will need to ask that person to help you. You…

The alarmists are taken aback by the fact that AMD has installed this cooler; they are the ones who are astonished. The issue can be resolved with just a small bit of physical strength (even your girlfriend is capable of handling it). And who are we trying to kid — if you read reviews on a cooler that costs $900, then you probably don't have it). The verdict is that it is quite adequate for non-extreme overclocking. With all of its perks. The temperature of a Phenom x955 that has been…

I did that for 38 years and am as content as a happy elephant. If I had a spare percent, I'd rather put it toward something else. Because of this, I believe that investing in this option is the best use of your money, and I encourage you to do so! Has pros: 1) The operation is extremely low-key in terms of noise 2) Has an extremely chilly temperature AMD Phenom X4 2800 MHz in overclocking 3300 and under load regular from 68 g (and generates noise similar to that of a Boeing 747 taking off) the…

Pros: very quiet. cools the i5-2400 processor at a temperature of 17-22 degrees. (I'm worried that I won't freeze). Different cons: Installation is inconvenient. thermal paste is thick and sticks to the finger.

With its pros. fits on different sockets, I stood on am2, migrated to 1155. holds i5 2500k not overclocked in a load of 55C with kpt-8. on asus p8p67 does not interfere with slots. quite quiet. Has some cons slightly imperfect surface, can be polished. and may not be polished.

This cooler comes in two different builds: standard and deluxe. 1) Using clips that are straight 2) Contouring (for AMD) directly within the AMD FX 8320 itself. If you come across curved ones, then you are in luck because installing a cooler is a child's play; however, if you come across straight lines, like I did, then you need a little thought and ideally hands. We first secure the sticks, then attach the backplate to the mother after placing the clips in the sticks (there are many examples…

As a replacement, I purchased the Cooler Master S200, and Zalman tower coolers are generally considered to be of GREAT quality. I purchased a new one for only 1700 dollars to cool the Core i7-4790 (the paste was included in the kit and it was zalman zm-stg2, which was thick but smeared perfectly), and as a result, the temperature is as follows: when it is not being used, it is between 28 and 30, and when it is being used, it does not rise above 58. It turned out that the unnecessary plate in…

In general, a good cooler is one that cools well, as this is the primary function that it serves. excellent for overclocking purposes. I agreed to take it for 1100 kopecks, but he insisted on charging his money for all 100. Although it is recommended to take the current, keep in mind that not all cases will fit. Many advantages: excellent ice chest. idling temp ~30 degrees. under load, the Intel Core i7-860 reached temperatures of 50-52 degrees Celsius while it was overclocked to 200 megahertz:

The Core i5 2500K that has been overclocked from 3.3 GHz to 4.6 GHz is kept cool by this cooler. During the LinX test, which places the processor under its greatest amount of load, the temperature does not exceed seventy degrees. While using the BOX chiller, the temperature reached 100 degrees. These are the temperatures when measured at 4.6 gigahertz. V Core is what is used by default. During periods of inactivity, the temperature drops to about 26-28 degrees. :)) Who cares about the results…

I was deciding between the Performa and the Flex, and while they are both good, the Performa was 200 R. cheaper, and it came with a fan already installed and was very quiet. The Flex, on the other hand, is more efficient at low speeds because the intercoastal distance is larger, and adding a second fan (I put 800 rpm to the standard Scythe SlipStream) lowers the temperature by 3-5 degrees. In general, it is a good cooler, and I would recommend it to anyone Phenom II 955BE @ 3.6 in overclocking,

Pros: It cools very well, the temperature was 69 degrees, it became 29)))) amd processor 4 cores I advise everyone Different cons: installation swearing for the whole house is simple) now I don’t close the big lid, but I made the backlight and everything is fine

Has pros: Really good cooling cooler, quiet, low price, anti-vibration pads. Cons: Installation is heavy (according to the book) P. S We must look at the off. site flash video on installation.

Pros: The temperature of the processor (6700) in overclocking has never risen above 50 degrees, I am satisfied with the purchase Some cons: With the installation of it was a little zapa, but this can not be called a disadvantage))

Finally managed to get to the computer in order to complete the review for this product. The Zalman, TT, and CoolerMaster brands are some of my favorites, however I have to say that I was let down by this cooler. Stone 2550k has an increased clock speed of 4.5 MHz. 45 degrees. The graphics are intuitive for each and every aspect. The cooling is done quite well. Everything would go off without a hitch. However, I noticed a hum, similar to that of a transformer. In addition, the hum was…

It's a pretty decent cooler for the price. He makes short work of the challenges he faces in his work. If you replace the fan, you will notice that it is much quieter. Take it, you won't regret it. However, in comparison to equivalents produced by other manufacturers, its installation into the motherboard will be more difficult. When installing this cooler, exercise extreme caution. Many advantages, including: - Universal, compatible with any and all sockets - The native fan is equipped with a…