How to set the desired water temperature?
Setting the right water temperature on your Kingwork bucket water heater is important for comfort and safety. Here are the steps to set the desired temperature:
1. Understand the temperature settings
The Kingwork heater has a thermostat with temperature settings from 95°F to 155°F. Consider your needs:
- 120°F - 140°F for most residential uses like washing hands, dishes, etc.
- 130°F - 155°F for high temperature cleaning/sanitation
- 95°F - 105°F for uses around children/elders
2. Locate the thermostat
On the Kingwork heater, the thermostat knob is on the front near the power cord. It has temperature markings and an indicator arrow.
3. Adjust the thermostat
Turn on the heater and let the water heat up. When it reaches the desired temperature:
- Turn off the heater and unplug it.
- Rotate the thermostat knob to align the indicator arrow with the desired temperature.
- Plug the heater back in and turn it on to verify the new setting.
Repeat steps until the temperature is right. The thermostat will maintain this temperature automatically.
4. Test the water temperature
For safety, always test the water temperature before use with a thermometer or by touch. Adjust the thermostat again if needed.
Setting the right temperature on your Kingwork water heater is quick and easy following these steps. Proper temperature settings will allow you to get the most efficient and safe use out of your heater.
How to install and use the water heater properly?
Installing and using the Kingwork bucket water heater correctly will ensure efficient, trouble-free operation. Here are some tips:
Similar products
Choosing a location
- Select a stable, level surface like the floor or countertop near the sink.
- Ensure the electrical outlet is reachable with the power cord.
- Allow at least 12 inches clearance on all sides for airflow.
- Do not install in bathroom or other wet locations.
Filling with water
The Kingwork heater holds 5 gallons of water in its tank. To fill:
- Remove the lid on top of the tank.
- Use a hose or bucket to fill with clean tap water to the maximum fill line inside the tank.
- Replace the lid securely.
Heating the water
Once filled, plug in the heater and turn it on. The 1500W heating element will bring 5 gallons of water to temperature in around 15 minutes. Set the thermostat knob to the desired temperature setting. The auto shutoff will kick in once it reaches temperature.
Using the hot water
Dispense hot water using the side drain valve. Open the valve and fill containers by placing below the drain. The Kingwork heater can produce over 50 gallons per hour of hot water continuously. Take precautions against burns by testing water temperature before use. Unplug unit when not in use.
Maintenance
To keep your Kingwork water heater working efficiently:
- Drain and refill tank monthly to prevent scale buildup.
- Descaling solution can be used periodically for heavy scale.
- Inspect heating element and connections to ensure no damage or leaks.
- Never operate unit without water in the tank.
By selecting a good location, proper filling and heating, and periodic maintenance, your Kingwork bucket water heater will provide reliable hot water for your needs.
How to maintain the water heater for longevity?
With proper maintenance, you can extend the life of your Kingwork bucket water heater and ensure it continues providing hot water when you need it.
Drain and flush regularly
Mineral deposits and sediment from the water supply can build up in the tank over time. To prevent this:
- Drain tank monthly by opening the drain valve and letting all water empty out.
- Flush tank with clean water to wash out any residues.
- If heavy scale is present, fill tank with descaling solution and let soak for 15-30 minutes before draining.
Inspect the heating element
The 1500W heating element heats the water in the tank. Check it periodically for:
- Burned out coils or broken insulation
- Corrosion from water deposits
- Loose electrical connections
Replace the heating element immediately if any issues are found to prevent more damage.
Check valves and fittings
Examine all plumbing connections and valves on the heater for:
- Mineral deposits or corrosion
- Drips or leaks
- Cracks or damage
Tighten any loose fittings. Replace any worn out o-rings or valve parts as needed.
Test thermostat accuracy
Make sure the thermostat maintains the set temperature consistently. Test with a thermometer and adjust or replace thermostat if more than 5°F difference.
Inspect power cord and wiring
Check the power cord and all internal wiring for:
- Fraying or exposed wires
- Loose connections
- Cracks in insulation
Have a qualified electrician make any needed wiring repairs immediately.
With periodic maintenance to remove scale buildup, inspect all components, and make repairs as needed, you can keep your Kingwork water heater running efficiently for years to come.
Top products in 🚿 Water Heaters & Parts
How to troubleshoot common issues with the water heater?
Even quality water heaters like the Kingwork can sometimes develop problems. Here are tips for diagnosing and fixing the most common issues.
Water not getting hot
If the water isn't heating up, check for:
- Power - verify the unit is plugged in and outlet is working.
- Thermostat setting - ensure not set too low.
- Heating element - inspect for damage or corrosion.
- Wiring - check all connections are tight.
Water not warm enough
If the water only gets lukewarm, it could be:
- Scale buildup in tank - drain and descale the tank.
- Thermostat out of calibration - test and adjust.
- Insufficient heating element - replace if corroded or coils broken.
Water too hot
If the water is dangerously hot:
- Thermostat set too high - turn down to lower temperature.
- Thermostat stuck closed - replace thermostat.
- Element stays on - replace heating element.
Leaking water
If you notice water dripping/leaking, check:
- Plumbing fittings - tighten/replace o-rings and washers as needed.
- Valves - remove scale buildup and sediment.
- Tank - inspect seam and welds for cracks or holes.
Noisy heating or bubbling
Excess noise can mean:
- Sediment buildup in tank - flush and drain tank.
- Water level too low - ensure filled to maximum line.
- Damaged heating element - replace if deteriorated.
Taking the time to properly diagnose and fix any issues with your Kingwork heater will have it running like new again quickly.
How To Install Kingwork Bucket Water Heater?
Installing the Kingwork Bucket Water Heater is a simple process that can be done in a few easy steps. Here's how to do it:
- Fill a bucket or other container with water.
- Immerse the Kingwork Bucket Water Heater in the water.
- Plug the heater into a power outlet.
- Use the thermostat to set the desired temperature.
- Wait for the water to heat up to the desired temperature.
- Once the water is heated, unplug the heater and remove it from the water.
- Empty the water from the bucket or container.
Another interesting products
30 Review
32 Review
Where Can I Buy The Kingwork Bucket Water Heater?
The Kingwork Bucket Water Heater can be purchased from various retailers, including:
It's important to note that availability and prices may vary depending on the retailer and the time of purchase.
