Header banner
Revain logoHome Page
๐Ÿ› ๏ธ creality original 3d extruder assembled: enhanced performance with easy setup logo

๐Ÿ› ๏ธ Creality Original 3D Extruder Assembled: Enhanced Performance with Easy Setup Review

3

ยท

Poor

Revainrating 2.5 out of 5ย ย 
Ratingย 
2.3
๐Ÿ–จ๏ธ 3D Printer Parts & Accessories, ๐Ÿญ Additive Manufacturing Products

View on AmazonView on ะฏM

Media

(2)
img 1 attached to ๐Ÿ› ๏ธ Creality Original 3D Extruder Assembled: Enhanced Performance with Easy Setup
img 2 attached to ๐Ÿ› ๏ธ Creality Original 3D Extruder Assembled: Enhanced Performance with Easy Setup

Description of ๐Ÿ› ๏ธ Creality Original 3D Extruder Assembled: Enhanced Performance with Easy Setup

ENDER 3 EXTRUDER is 100% ORIGINAL CREALITY 3D PRINTINGE PRINTERS PARTS /ACCESSORIES AND WITH HIGH QUALITY, WE JUST CONFIRM IT WORKS WITH CREALITY ENDER 3 3D PRINTERS. OTHERS BRANDS WE DO NOT TEST IT. 5 PIECES 0.4MM 3D PRINTERS NOZZLES AS GIFT. ENDER 3 EXTRUDER HOT END CAN WORK WITH DIFFERENT SIZE MK8 NOZZLE: 0.2MM 0.3MM 0.4MM 0.5MM 0.6MM 0.8MM 1.0MM NOZZLE. MK8 EXTRUDER HOT END KITS,WHITE WIRE WAS TEMPERATURE THERMISTOR, BLACK WIRE WAS HEATING TUBE 24V 40W. TIP OF NOZZLE, ALUMINUM HEATING BLOCK, THROAT PIPE (BUILT-IN TEFLON).

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    2

Type of review

Revainrating 1 out of 5

Works good but not as good

I bought this to replace a hot end 5 part that broke. Overall my experience was positive but I join the stars because the item I received did not match what I had replaced what was advertised. The wires are thinner. The original had thicker wires, 2.0mm OD versus 1.7mm. While this does not affect performance, it is a concern.2. Wires have no terminals. My originals had CNDZ C5 connectors for quick disconnect. The new ones were bare wires that had to be screwed into the motherboard.3. The hoseโ€ฆ

Pros
  • NOZZLE TIP, ALUMINUM HEATER BLOCK, PIPE (TEFLON INTEGRATED)
Cons
  • Not sure

Revainrating 5 out of 5

Shorting Wires for Ender 3

Does not fit my Ender 3! Firstly I loved this hot end, it not only came with improved insulation (mine was the old taped one) but also a blue teflon coating. A tube! Although it's made for a printer half the size when worn. The wires were half the length of my original hot end, which I took out. Path. higher and will not extend it left and right the full distance. Not sure about the Ender 3 Pro, but my Ender 3 had green posts that you screw the hot-end wires into. The wires were not only short,

Pros
  • ENDER 3 EXTRUDER IS 100% ORIGINAL CREALITY 3D PRINTED PARTS/ACCESSORIES AND HIGH QUALITY, WE ONLY CONFIRM THAT IT WORKS WITH CREALITY ENDER 3 3D PRINTER.
Cons
  • Questionable purchase for the elderly

Revainrating 1 out of 5

Installation in Ender 3

This was my first time replacing my hotend and I was very nervous that I would do permanent damage. Luckily it wasn't as difficult as I expected. The part is the same as the one that came with my Ender 3, it is rated for 24v so read the fitting instructions that came with your Ender before purchasing. 3 and make sure you have 24v (some seem to be 12v). Mine came with the same silicone sock but it seems like some of the older ones only have the captain's strap and if that's the case with yoursโ€ฆ

Pros
  • 5 pcs. 0.4MM NOZZLE FOR 3D PRINTER AS GIFT.
Cons
  • So far so good