Header banner
Revain logoHome Page
πŸ”Œ silicone throttle body hose for subaru wrx 2008-2014 - mishimoto mmhose-sub-itbbk (black) logo

πŸ”Œ Silicone Throttle Body Hose for Subaru WRX 2008-2014 - Mishimoto MMHOSE-SUB-ITBBK (Black) Review

9

Β·

Very good

Revainrating 4 out of 5Β Β 
RatingΒ 
4.1
πŸ”§ Emission System, 🏎️ Performance Car Parts & Accessories

View on AmazonView on Π―M

Media

(1)
img 1 attached to πŸ”Œ Silicone Throttle Body Hose for Subaru WRX 2008-2014 - Mishimoto MMHOSE-SUB-ITBBK (Black)

Details

BrandMishimoto
MaterialSilicone
ColorBlack
Item Dimensions LxWxH4.25 x 3.25 x 3 inches
Item Weight0.4 Pounds

Description of πŸ”Œ Silicone Throttle Body Hose for Subaru WRX 2008-2014 - Mishimoto MMHOSE-SUB-ITBBK (Black)

Compatible with 2008-2015 Subaru WRX. INNER DIAMETER: 2.75" OUTER DIAMETER: 3.15". Maximum Temperature: 330Β°F. Constructed with high grade silicone and heat-resistant embedded fibers.

Reviews

Global ratings 9
  • 5
    5
  • 4
    2
  • 3
    1
  • 2
    0
  • 1
    1

Type of review

Revainrating 5 out of 5

Nice update for leaky TB hoses.

I bought this to replace a leaking TB hose. Follow the other reviews and the installation should go smoothly. As others have reported, I wish the tubing was a bit longer (maybe 0.5-1 inch) so alignment isn't necessarily perfect and there is some clearance. The quality seems good and I love that they provided new clamps.

Pros
  • Weight
Cons
  • I don't remember

Revainrating 4 out of 5

Fits Wrx 2015+ Emissions

Mishimoto website says it fits Wrx 15+. I went to a link and ordered it. Fits perfectly. The little dimple goes straight down and the words go straight up (but in reverse, as if you were reading them from the driver's seat). Installation took about 20 minutes with only one adjustment. If there is a gap at the bottom of the intercooler, face the lettering towards the driver. I have the perfect one for everyone around me. In terms of quality, it feels like any other decent silicone clutch. Only 2

Pros
  • Annual Test
Cons
  • No

Revainrating 3 out of 5

As everyone said: vacuum t-shirts

[photo update only] once I filed and didn't care about the gap everything is fine. As another reviewer said, installation should be easy, but it was still so difficult. The logo or dimple as a landmark does not matter. Whichever way you go, it just won't fit. I had to file the angled edge of the TMIC to keep it from poking through the tubing. (when the dimple is facing down where it fits better than the other). Still gives a slight gap but seems ok (from another reviewer). There is no leak at…

Pros
  • cool product
Cons
  • so-so

Revainrating 5 out of 5

2005 LGT also works

Used for 2005 LGT Wagon, 185k Car has pipes leaking everywhere, this is the last one I replaced and well worth the money. There was a boost leak on the stock engine, they replaced all the vacuum lines, the turbo intake pipe, the intercooler and finally that throttle body intercooler pipe. The hesitation is gone and seems to work better. For installation I had directed the logo to the intercooler. There was also a problem with the engine mounts on the driver's side. I could not align the two…

Pros
  • New
Cons
  • Has defects

Revainrating 1 out of 5

Doesn't fit my 2011 WRX

No matter how I tried to align the hose, logo side up, down and sideways, after two hours of fighting I still couldn't get the hose on. It's just too long, and its position alongside the stock hose confirms that. This will constantly move the intercooler too far out of alignment and put a lot of extra pressure on the bolts. I didn't want to risk cutting off my old turbo bolts, so I put the stock hose back on. I don't know how you could install this hose other than modifying either the hose or…

Pros
  • Few competitors
Cons
  • Not as thick as other picks

Revainrating 4 out of 5

13 WRX Boost Leak Fixed

Nobody will buy this part unless they are faced with a horrific general boost leak for our vehicles. I'm giving this part 4 stars because I wish I had at least some assembled instructions. I mean they have a youtube video on installation but I would rather just see a piece of paper showing how to remove the intercooler with screws here and here, disconnect the BPV, remove, attach the hose like this, attach the intercooler . and go choo-choo with proper boost and better idle. The part appears to

Pros
  • Nice Packaging
Cons
  • Functionality

Revainrating 5 out of 5

Fixed my hesitation issues - JDM 2007 Subaru Legacy GT

Very easy to install, good quality product! I've been looking for a low RPM problem for quite some time. and after some research our factory throttle body hoses have been known to wear out over time. I didn't bother resetting my ECU and decided to let the car relearn. There were still fluctuations, but after a few days of driving they were almost 100% gone! Just a tip, the hose is quite stiff and stiff out of the box so please remember to retighten the hose clamps after a few days of riding as…

Pros
  • High marks for support and durability from testers
Cons
  • Questionable purchase for seniors

Revainrating 5 out of 5

Is there a leak? Just buy it already.

After several attempts to repair my Wrx 12 OEM hose by removing the bushings, adjusting the clamps and moving it, I finally gave in and got this hose. I've had my eye on it since day one, but while it's inexpensive I didn't want to pay that much for an inner tube. and to say that I am happy with my purchase. I've heard they came with T-bolt clamps but to be honest I don't know how I would mount them, the clamps supplied seem better than stock. Or maybe it's just because they're new. For those…

Pros
  • Great for a small home
Cons
  • Negative impression

Revainrating 5 out of 5

Mandatory replacement for 11-14 WRX

I had a really hard bump and the car jerked as the revs rose between 1st and 2nd and 2nd and 3rd gears. Even after tightening the OEM hose from the throttle body to the intercooler, I heard a hissing sound as the car pulled very hard with the boost on. Everyone I knew recommended this Mishimoto hose with reinforced clamps. Apparently this is a known issue with the 2011-2014 WRX. From reading other sites I bought an HPS 76-84mm "T-Bolt" clamp which uses a 10mm socket to tighten the nut. The…

Pros
  • Good product for the price
Cons
  • weak