Header banner
Revain logoHome Page
๐ŸŽธ salecom position guitar toggle switches for industrial electrical applications logo

๐ŸŽธ SALECOM Position Guitar Toggle Switches for Industrial Electrical Applications Review

3

ยท

Very good

Revainrating 4.5 out of 5ย ย 
Ratingย 
4.7
๐Ÿ”Œ Electrical Controls & Indicators, ๐Ÿ’ก Industrial Electrical

View on AmazonView on ะฏM

Media

(3)
img 1 attached to ๐ŸŽธ SALECOM Position Guitar Toggle Switches for Industrial Electrical Applications
img 2 attached to ๐ŸŽธ SALECOM Position Guitar Toggle Switches for Industrial Electrical Applications
img 3 attached to ๐ŸŽธ SALECOM Position Guitar Toggle Switches for Industrial Electrical Applications

Description of ๐ŸŽธ SALECOM Position Guitar Toggle Switches for Industrial Electrical Applications

Mini Toggle Switch threaded bushing height: 5/16"; Bushing Diameter: 1/4"; Cavity Depth: 5/8". Mini Toggle Switch 3 Position ON/ON/ON (3A 250VAC/5A 125VAC); Comes with 2 nuts, a flat and a lockwasher. These are good quality toggle switches, not cheap and inferior toggle switches. Please be sure to verifgy the dimensions carefully before you order the item. Please contact us when you have problem with the item before leaving feedback, we will try our best to serve you as soon as we receive your message.

Reviews

Global ratings 3
  • 5
    2
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 4 out of 5

Used this to change my pickup selector switch from Neck/Bridge to Neck/Both/Bridge. Works perfectly!

My guitar's previous owner installed a 3-pin latching mini ON/OFF/ON switch so I could only use one pickup at a time and I wanted to expand the guitar's capabilities so I could Pickup can mix . Installed that and it worked great. At 320 there are no soldering issues and the switch sounds very clean when amplified. The only downside is that this switch is slightly larger than the Revain 3 pin ON/OFF/ON switch so the hex ring, washer and rubber switch cover from the old switch will not fit. Youโ€ฆ

Pros
  • Free for educational purposes
Cons
  • Not sure

Revainrating 5 out of 5

Note which way the switch is pointing.

I needed a mini on/on/on toggle switch to build a guitar. Everyone in the world has a DPDT, 6-pin, 3-position switch. But most of them are on/off/on - be very careful if you want on/on/on because they look exactly like on/off/on. .When you use them, the center pins are your input and output respectively (it doesn't matter which center pin you use for what). You'll see a notch cut into one side of the switch's threaded stem, and I haphazardly thought that would be the "first position". Howeverโ€ฆ

Pros
  • Absolute Legend
Cons
  • Great Price

Revainrating 5 out of 5

Great switch. There are two types of enable/disable/enable. Make sure you know which one you have before connecting.

Great little switch. There are two types of on/on/on switches: Make sure you have/need the configuration you think you will make. ;) Good workmanship (do not overheat!), great price, delivery on time. a full pass between the terminals, solder the first leg [exactly where the strip *ends*], then cut off the stripped/discarded insulation a bit [to leave room for solder on each end] and lay it down back onto the pre-stripped end protruding from the just soldered ferrule (easier with solid thanโ€ฆ

Pros
  • Dope ๐Ÿ”ฅ
Cons
  • Expensive