Header banner
Revain logoHome Page
πŸͺ‘ ezprotekt adjustable furniture riser base for chair, table, desk, sofa- fits feet diameter 1-1/8" to 1-5/8" - height adjustable from 2-5/8" to 4" - 0Β°~45Β° rotatable - 4pack black logo

πŸͺ‘ Ezprotekt Adjustable Furniture Riser Base for Chair, Table, Desk, Sofa- Fits Feet Diameter 1-1/8" to 1-5/8" - Height Adjustable from 2-5/8" to 4" - 0Β°~45Β° Rotatable - 4Pack Black Review

3

Β·

Very good

Revainrating 4.5 out of 5Β Β 
RatingΒ 
4.3
πŸ›οΈ Bedding Accessories, πŸ›Œ Bedding

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸͺ‘ Ezprotekt Adjustable Furniture Riser Base for Chair, Table, Desk, Sofa- Fits Feet Diameter 1-1/8" to 1-5/8" - Height Adjustable from 2-5/8" to 4" - 0Β°~45Β° Rotatable - 4Pack Black
img 2 attached to πŸͺ‘ Ezprotekt Adjustable Furniture Riser Base for Chair, Table, Desk, Sofa- Fits Feet Diameter 1-1/8" to 1-5/8" - Height Adjustable from 2-5/8" to 4" - 0Β°~45Β° Rotatable - 4Pack Black
img 3 attached to πŸͺ‘ Ezprotekt Adjustable Furniture Riser Base for Chair, Table, Desk, Sofa- Fits Feet Diameter 1-1/8" to 1-5/8" - Height Adjustable from 2-5/8" to 4" - 0Β°~45Β° Rotatable - 4Pack Black
img 4 attached to πŸͺ‘ Ezprotekt Adjustable Furniture Riser Base for Chair, Table, Desk, Sofa- Fits Feet Diameter 1-1/8" to 1-5/8" - Height Adjustable from 2-5/8" to 4" - 0Β°~45Β° Rotatable - 4Pack Black

Description of πŸͺ‘ Ezprotekt Adjustable Furniture Riser Base for Chair, Table, Desk, Sofa- Fits Feet Diameter 1-1/8" to 1-5/8" - Height Adjustable from 2-5/8" to 4" - 0Β°~45Β° Rotatable - 4Pack Black

β™œ[CHECK SIZE BEFORE PURCHASE]: Fits round furniture legs with diameter from 1-1/8" to 1-5/8". WARM TIPS: 1.PLEASE MEASURE THE SIZE OF YOUR FURNITURE LEGS CAREFULLY BEFORE ORDERING. β™œ[ADJUSTABLE]: Super solid chair and furniture riser can be altered with spiral design. Rotate to adjust height from 2-5/8 inch to 4 inch, creates an additional height or storage and has the greatest furniture post distance. β™œ[ROTATABLE]: Support 45Β° horizontal rotation and 360Β° circular rotation. Rotate struts for optimized bedpost direction and position. Rotate the base joint to find the perfect angle for your furniture. Adjust the angle could also use for slanted furniture legs. β™œ[HEAVY ZINC ALLOY DUTY TOWER]: It won't crack like other lifters. Zinc Alloy Will NOT BEND or BREAK. Great for Chairs, Beds, Couches, Armchairs, Desks, Sofas, and more. Lifts from 2-5/8 to 4 inches for stationary items. Besides, our bed risers with the bottom of non-woven fabrics design will provide great protection for your floors. β™œ[GUARANTEE]: 100% crack free warranty from registered brand on amazon. Other risers crack easily in spite of assurances and that has become the highest rated complaint of consumers but Ezprotekt risers offer 100% warranty against cracking and have been tested to hold over 500 pounds per leg.

Reviews

Global ratings 3
  • 5
    2
  • 4
    0
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Great chair lifts

I needed chair lifts for my narrow legged dining room chairs and they worked great. It doesn't look strong, but it really is. I was concerned because my chair legs are angled like most dining room chairs. I've only had them a week, but I'm satisfied. It was hard to find exactly what I needed anywhere.

Cons
  • Exterior

Revainrating 5 out of 5

Looks good and does the job

There is a couch with a cot underneath. The clamshell was difficult to pull out, there wasn't enough clearance. These chairs were perfect. There were some issues installing the legs into the rails due to the plastic ring. The legs of the bed were a bit too big to easily fit in the ring, but a sharp push and it was done. Looks good, the clamshell slides out easily.

Cons
  • Can't remember

Revainrating 3 out of 5

Worked great for raising the day bed to allow the cart to slide in and out but!

Not stable at all on a thick carpet. My bed riser with a wider base would not work with an under bed trolley. So I bought PVC fittings from Lowes which made it very stable by adjusting the bed's leg and lowering it onto the riser. Now it works perfectly. I would suggest doing them with a higher hem to keep the legs in place and stable. Now that the grandkids are coming we can just pull out the cot and now there is room to keep the bed made.

Cons
  • Operating speed