Header banner
Revain logoHome Page
laser marking powder: metals marking with co2, fiber, yag lasers - permanent, high contrast, brilliance laser inks - bli101mbpwd logo

Laser Marking Powder: Metals Marking with CO2, Fiber, YAG Lasers - Permanent, High Contrast, Brilliance Laser Inks - BLI101MBPWD Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.7
📝 Paper & Paper Crafts, 🧶 Crafting

View on AmazonView on ЯM

Media

(4)
img 1 attached to Laser Marking Powder: Metals Marking with CO2, Fiber, YAG Lasers - Permanent, High Contrast, Brilliance Laser Inks - BLI101MBPWD
img 2 attached to Laser Marking Powder: Metals Marking with CO2, Fiber, YAG Lasers - Permanent, High Contrast, Brilliance Laser Inks - BLI101MBPWD
img 3 attached to Laser Marking Powder: Metals Marking with CO2, Fiber, YAG Lasers - Permanent, High Contrast, Brilliance Laser Inks - BLI101MBPWD
img 4 attached to Laser Marking Powder: Metals Marking with CO2, Fiber, YAG Lasers - Permanent, High Contrast, Brilliance Laser Inks - BLI101MBPWD

Description of Laser Marking Powder: Metals Marking with CO2, Fiber, YAG Lasers - Permanent, High Contrast, Brilliance Laser Inks - BLI101MBPWD

✅ 100% SATISFACTION GUARANTEE OR MONEY BACK:Settings and marking techniques may vary depending on the laser and metal product being marked. We can usually resolve most marking issues with simple setting adjustments. Please feel free to contact us directly. ✅ FOAM BRUSH INCLUDED: Add denatured alcohol or similar RATIO 1:1. Mix/Shake well, Use foam brush to apply on the substrate surface, apply a thin coat using left to right motion, as long as you do not see through the surface.Use the suggested laser settings in our FAQ section as a starting guide line or feel free call our Technical Support Team. ✅ AIR BRUSH or SPRAY-GUN APPLICATION: Add denatured alcohol or similar. RATIO 1:2 or 1:3. Mix/Shake well before spray. ✅ GENERAL GUIDELINES ✅ SETTINGS: Scan QR CODE on product label to see our suggested laser settings in our FAQ section of our website. CO2 LASER - 25 Watt Minimum Required (100% P / 15-30% S / 500-700 DPI). FIBER LASER - 10 Watt Minimum Required (@ 10 Watt PWR / 50 mm/sec / 80-500 Q-Freq. / DPI- 0.1mm Hatch) Low watt Diode Lasers are not recommended. ✅ DRIES QUICKLY ✅ NO WAIT REQUIREMENT: To further speed up the process use hair dryer or heat gun to dry within seconds.

Reviews

Global ratings 3
  • 5
    2
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 1 out of 5

No luck so far

I can't figure out the correct settings for the K40 CO2 laser and it looks like the vendor has blocked questions here so I can't ask for success. But there was no success with the 40-watt K40 laser at high and low settings.

Pros
  • Great for me
Cons
  • No instructions

Revainrating 5 out of 5

Works as advertised!

I've found this powder concentrate to be a cost effective way to achieve excellent quality markings on metals and stainless steel, especially for large scale mass production. Use an air spray, but a brush will also work. Received an excellent seal of quality as stated. I applied a light coat of No See Through Rule and it works like a champ.

Pros
  • Satisfied
Cons
  • I'll get back to you later

Revainrating 5 out of 5

What an AMAZING PRODUCT!

This product exceeded my expectations. I don't normally write reviews but due to the value of this product I was compelled to do so. Similar items on the Revain list cost more, but this is a great job for less money. Very happy with the results and practical use of Black Laser Ink, they do exactly what they say they do! Will buy again! Thanks for the great value!

Pros
  • Absolutely amazing!
Cons
  • Not bad, but...