Header banner
Revain logoHome Page
πŸ”† simpo horizontal retrofit replacement 3000 3500k: advanced lighting solution for vast horizontal spaces logo

πŸ”† Simpo Horizontal Retrofit Replacement 3000 3500K: Advanced Lighting Solution for Vast Horizontal Spaces Review

3

Β·

Average

Revainrating 3.5 out of 5Β Β 
RatingΒ 
3.7
πŸ’‘ Lighting Components, πŸ’‘ Industrial Electrical

View on AmazonView on Π―M

Media

(3)
img 1 attached to πŸ”† Simpo Horizontal Retrofit Replacement 3000 3500K: Advanced Lighting Solution for Vast Horizontal Spaces
img 2 attached to πŸ”† Simpo Horizontal Retrofit Replacement 3000 3500K: Advanced Lighting Solution for Vast Horizontal Spaces
img 3 attached to πŸ”† Simpo Horizontal Retrofit Replacement 3000 3500K: Advanced Lighting Solution for Vast Horizontal Spaces

Description of πŸ”† Simpo Horizontal Retrofit Replacement 3000 3500K: Advanced Lighting Solution for Vast Horizontal Spaces

2-Pack 4W 2Pin G23 LED Bulb, Can Work with Inductance Ballast, BUT CAN NOT work with Electronic Ballast,so if the fixture has an Electronic ballast, Please DON'T plug directly, BYPASS ballast First!. 380-450lm Low heat, as we have not run all of the LED Power, make sure there is less light attenuation, and keep a longer life and sustainable light performance. Length 135mm/5.3"*D27mm/1.0" , replace CFL PL-S 7W Please check your old fixture allowed install length. Replace Compact Fluorescent Lamps/CFL widely used in Recessed/Surface-mounted Down lights, Recessed Cans, Table/Desk Lamps, Portables, Pendant Lamps, Ceiling Fixtures, Wall Washers, Wall Sconces, Family Rooms, Living Rooms, Kitchens, Dining Rooms, and Porches. Both 110V 220V AC CRI>82 high brightness 2835 SMD, Warm White 3000K Daylight 6000K Optional.

Reviews

Global ratings 3
  • 5
    2
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 5 out of 5

Bright light, well suited for the socket. Beautifully designed.

Ordered to replace the lamp on my old commercial embroidery machine. It fit well in the socket, but unfortunately was not compatible. It just keeps blinking and there is no ballast on the embroidery machine that needs to be bypassed for it to work properly. Sent back for a refund. If it were compatible that would be great!

Pros
  • 2-pack 4W 2Pin G23 LED bulb, can work with inductive ballast BUT NOT electronic ballast. So if the light has an electronic ballast, please DO NOT connect it directly, BYPASS the ballast first!
Cons
  • Miscellaneous Miscellaneous

Revainrating 5 out of 5

These are very good bulbs

Lighting in just one direction means much more efficient use of light and being LED it consumes less power than fluorescent lamps. The radiator also makes a solid impression. The fact that they're rated for up to 300V means you don't have to remove the ballast, which is very handy. I only wish they were in the G24Q base type too! (This is the more common basis for recessed lighting in the kitchen.)

Pros
  • Both 110V 220V AC CRI>82 High Brightness 2835 SMD Warm White 3000K Daylight 6000K Optional
Cons
  • Crumpled Packaging

Revainrating 1 out of 5

They are fully suitable for LED bulbs

These bulbs fit very loosely compared to my 7w PL-S fluorescent bulbs. You have to wiggle them in the plug to make them light up and work, and just hope they stay. I just measured the square plastic base on both lamps that fit in the socket. The new replacement LED bulb is 0.51" wide and 0.50" deep. The old original fluorescent base is 0.525" wide and 0.62" deep. No wonder they hang out at my outlet. Bad quality control. I'll keep going and see if they work.

Pros
  • length 135mm/5.3in * D27mm/1.0in, replaces CFL PL-S 7W Please check the permissible installation length of your old light.
Cons
  • write later