VSDISPLAY Controller M170ETN01 1 WYD170SKD Monitor - High-Performance Display with Enhanced Controller Review

I have a 1up Galaga and wanted a 60 in 1 board. I got it for a video adaptation and it worked great. The only thing is that the monitor cable is connected to the board anyway, and the only thing I thought was a key, in fact it wasn't. The cable was missing a 3rd wire on one side and the board was missing a pin on the 3rd wire on one side. I leveled this up and turned it on to find the monitor was not working. After 1.5 hours of troubleshooting I swapped the cable and it worked fine. Otherwise…

Ideal for modified Arcade1Ups with BOE monitors. I have a Gen 1 cockpit modified with the ArcadeModUp modpack (Gameroom Solutions) but the Gen 1 screen was broken so I replaced it with a BOE monitor from the newer A1Up cockpit. First I tried to use another LCD converter but the screen was not centered. So I bought this new LCD converter and it solved the problem and is working great now.

This board instantly solves the screen clipping problem for Gen 3 cases! I had this problem with a previous board and when I replaced it with this one it went away immediately. I've also encountered occasional issues with screen tearing or when half the screen is blank or has lines. Since replacing my board with this one, I no longer have these issues. If you need to know the model of your Arcade1Up monitor, look at its back cover. You will find it easy.

First I had a problem with the board I got from seller "Shenzhen Weisi Electronics Co. Ltd"and they went ahead to help me solve the problem including sending replacement boards. Thumbs up for you! Thanks! What I saw was a bunch of small horizontal lines all over the picture, moving very fast. I installed the board in several places in my Arcade1up case, without success. After many diagnostics, it turned out that my problem was an insufficient grounding issue where the factory ground strap for…

Used this from a YouTube video to change my TMNT case. Tip: You can connect standard speakers to the 4 pins on the far right to amplify the sound. Watch a YouTube video on how to do this.

I've seen many YouTubers use this to mod their slots so I bought it and I have to tell you it works like a dream. Thanks for attention!

Works fine, no complaints, used to update 1up arcade. Make sure you select the correct one I made a mistake and the problem was fixed quickly.

I've used this to mod my 1up arcade cabinet and so far it's worked great and exactly as intended! It also came with a ground wire screw which was very helpful! Overall I am very satisfied with this product.

It worked just like I thought it would. Bought this item to upgrade my Marvel Cockpit. Good color and display. Easy to set up.

It works as it should. I can see what people are talking about when they mention LCD with white lines. I noticed that mine worked fine, then I tried to install the main chip which put a bit of strain on the LCD cable and when I loaded the case I noticed the lines. So I removed the chip and removed the voltage and the white lines are gone, I'm not sure if it will work for other people but it worked for me.

Worked for my display as advertised. No problem. Just remember to turn the device off and on again after a power outage to restart it.

Make sure you have the correct card for your display device. I ordered the wrong one and can't blame anyone because the compatibility stats are right there on the product page, you just have to read. It was correct and works great. I didn't need a power supply because I only used it for my display device to power the display and the map.

I was skeptical when I read on Reddit about the lack of a working controller for Gen3 LCDs, but it works with no issues. However, one has to figure out how to turn the power on and off for the entire setup.

Ordered but it didn't work, it was replaced after 2 days, great time and communication. I had the circuit board replaced before sending in the defective one. The new one works perfectly! Thanks!

Worked great for my Marvel Arcade1Up cabinet. No clipping at the bottom of the screen, very easy to install I got this lcd controller to mod my Marvel Arcade1up and it worked perfectly without any screen cut off!.

Worked great with the Arcade1up Final Fight cabinet. I had an issue with my first order, but the seller responded quickly and fixed the issue for me. I would recommend it to anyone looking to mod the Arcade1Up case!

It's just what I need for my superhero wonder to speak. Despite trial and error and incorrect pricing on the 1st generation machines, things worked out great with the 2nd generation machine.

Works perfectly! Converts my 1up machine to a RetroPie system. Installing the board didn't take long. Very good quality and performance.

ARCADE1UP/RASP PI: Works great on my Mortal Kombat 1up. Don't pull the bottom too tight or strange artifacts will appear on the screen.

It does everything I need and even has amplified audio channels to feed directly into my speakers. It's a bit more expensive than other converter boards, but it gets the job done right.