Header banner
Revain logoHome Page
bczamd upgraded cartridge accessories extruders additive manufacturing products logo

BCZAMD Upgraded Cartridge Accessories Extruders Additive Manufacturing Products Review

3

·

Very good

Revainrating 4 out of 5  
Rating 
4.0
🖨️ 3D Printer Parts & Accessories, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to BCZAMD Upgraded Cartridge Accessories Extruders Additive Manufacturing Products
img 2 attached to BCZAMD Upgraded Cartridge Accessories Extruders Additive Manufacturing Products
img 3 attached to BCZAMD Upgraded Cartridge Accessories Extruders Additive Manufacturing Products
img 4 attached to BCZAMD Upgraded Cartridge Accessories Extruders Additive Manufacturing Products

Description of BCZAMD Upgraded Cartridge Accessories Extruders Additive Manufacturing Products

Apply to Creali CR-10S Pro, CR-X, Ender 3, Ender 3X, Ender-3 Pro, A8 A6, Maker Select V2.1, Wanhao Duplicator 3D Printer, V6 Volca MK8 MK9 MK10 Extruder/Hotend etc. Tips: No need any connector, no need other splice things, directly cut the cover skin, decide how length you need, then connect to the board. Voltage: 12V(The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.); Power: 50W; Heating head size: 6 x 20mm; Heating head material: 304 stainless steel; Working Temperature: < 350 degrees. The improvement compared to ordinary red heating tube:1.From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, can bear higher temperature, and looks more beautiful. 2.From the original 40W power to 50W, the maximum temperature increases from 300-31¡æ to 340-350¡æ. Can be used with the new HT-NTC100K temperature thermistor. The electric heating element should be stored in a dry place and should not be damp. 3.The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.

Reviews

Global ratings 3
  • 5
    1
  • 4
    1
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 4 out of 5

Heats up quickly, direct replacement for the original heater

Bought because of positive reviews. The cables felt great, the added heat protection on the ends was an improvement over what I had. They heat up quickly and hold the temperature well. I'm using a self-powered 12v mosfet. The first one took 2 weeks. Installed a second one with a new power supply tonight. Hopefully this lasts longer and I'll update once I have more time with them.

Pros
  • 3D printer accessories
Cons
  • I will add later

Revainrating 5 out of 5

Strange performance, works great

Strange performance, but everything seems fine. The resistor turned out to be a 50 watt heater at 12 volts. You will typically see them at 40 volts for 12 volt heaters. Was way better than my crappy Anet heater which was 24 watts. The cables also appear to be a little better than the regular red heaters you see. This is on par with the e3ds heaters. The wire inside seems to have enough wire and I don't think they skimped on it. So far I've used the first of 3 and it hasn't caught fire.

Pros
  • Additive manufacturing products
Cons
  • Slightly dented

Revainrating 3 out of 5

Cheap and good - 3D printer accessories

I've used this for probably less than 200 hours printing at 230C for PETG and the first of the three has already stopped heat. It's not too expensive to replace, but it's the time it takes to replace any of them. Working with a wire loom is a pain. If you buy this make sure you don't connect it to the rest of the wires so if it burns out it will take 5 minutes to replace instead of an hour. The cable gets very hot, so take that into account when placing it and you'll hear the fan shroud cooling

Pros
  • 3D printer parts and accessories
Cons
  • Legacy model