Header banner
Revain logoHome Page
shark industries pn-12704 die grinder cut off wheels - 10 pack, 3-inch x 1/16” x 3/8” shark type-1 double-reinforced thin wheels, 54 grit, 25,000 rpm max (10 cutting discs) logo

Shark Industries PN-12704 Die Grinder Cut Off Wheels - 10 Pack, 3-Inch x 1/16” x 3/8” Shark Type-1 Double-Reinforced Thin Wheels, 54 Grit, 25,000 RPM Max (10 Cutting Discs) Review

6

·

Very good

Revainrating 4 out of 5  
Rating 
4.2
🔩 Power Tool Parts & Accessories, 🔧 Power & Hand Tools

View on AmazonView on ЯM

Media

(3)
img 1 attached to Shark Industries PN-12704 Die Grinder Cut Off Wheels - 10 Pack, 3-Inch x 1/16” x 3/8” Shark Type-1 Double-Reinforced Thin Wheels, 54 Grit, 25,000 RPM Max (10 Cutting Discs)
img 2 attached to Shark Industries PN-12704 Die Grinder Cut Off Wheels - 10 Pack, 3-Inch x 1/16” x 3/8” Shark Type-1 Double-Reinforced Thin Wheels, 54 Grit, 25,000 RPM Max (10 Cutting Discs)
img 3 attached to Shark Industries PN-12704 Die Grinder Cut Off Wheels - 10 Pack, 3-Inch x 1/16” x 3/8” Shark Type-1 Double-Reinforced Thin Wheels, 54 Grit, 25,000 RPM Max (10 Cutting Discs)

Description of Shark Industries PN-12704 Die Grinder Cut Off Wheels - 10 Pack, 3-Inch x 1/16” x 3/8” Shark Type-1 Double-Reinforced Thin Wheels, 54 Grit, 25,000 RPM Max (10 Cutting Discs)

Double-Reinforced Cutting Wheel – We’ve double-reinforced our abrasive cut-off wheels with fiberglass to provide added durability and longevity. Made in USA Cut-off Wheels – You can trust the materials and the manufacturing process used for our abrasive cutting wheels, as they are made in the United States. Perfect for cutting carbon steel, cast iron and general-purpose metal. Made for Aggressive, High-Speed Cutting – Our wheel can spin at a maximum speed up to 25,000 revolutions per minute. For safety, be sure to use with a guard. 10-Pack of Wheels – This kit has ten wheels, so you’ll always have plenty of cut-off wheels on hand to finish the job and to start the next one!.

Reviews

Global ratings 6
  • 5
    4
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 5 out of 5

Good cutting wheels

Good cutting wheels. Unfortunately, not all Sharks are from the US (buy 4.5-inch wheels, they're made in China), but they're nice to have. Good price and good durability. Cut faceplate.

Pros
  • Amazing
Cons
  • Problems

Revainrating 4 out of 5

Saw Blade Guide for Abrasive and Finishing Products

General Specification Sheets. I used to cut out the hood of a car to install blinds. In the end, all I needed was a saw blade. He made several cuts without affecting performance. I used it with Aircat's built in pneumatic parting tool. Very satisfied and highly recommended.

Pros
  • One Year Trial Period
Cons
  • Available in White Only

Revainrating 5 out of 5

Okay but you need to enlarge the holes a bit to work with the Proxxon tool.

No problems as advertised. Hard drives and good price per pack. I'm assuming the Proxxon is metric, so is the hole just over 3/8"? I had to use a 5/8" Dremel Cone Bur to enlarge the holes. Not a big deal, but an extra step for my application. Update: The Proxxon holes are 10mm, so yes some enlarging is required. Also, Harbor Freight 3" rims are made with 10mm holes so they fit both 3/8" and 10mm rims.

Pros
  • Consistent test results
Cons
  • Could have chosen a newer model

Revainrating 5 out of 5

Cute cutting tool. Add water cooling if you want!

I like these. Affordable and keeps a decent time. They are made in the USA and give a thin and clean cut. I have found that I can run them a little longer before they overheat compared to others. If you want to set up a simple water cooling station for your cutting tool, try this: Get a water bottle and some duct tape. Poke a small hole in a water bottle. Take a 3/8 inch vinyl tube (soft) and slide it through, wrap it with tape and pull to make sure it is snug. Take a hose clamp…

Pros
  • Sturdy construction
Cons
  • Not automatic