🔩 Power Transmission Products
3 Review
Effective on hard and soft shafts. Cost effective collar design for limited spaces. Easily installed where major disassembly would otherwise be required. Tolerance: +.0005/+.0030. Zinc plating provides moderate corrosion resistance.
3 Review
Model: HK0509 (Bore Dia. (Fw)= 5mm, Outer Dia. (D)a= 9mm, Width (C)= 9mm). ST14 Steel Drawn Cup, ST13 Steel Cage, GCr15 Needle Roller. Good heat tolerance, high load carrying capacity and stiffness. Low cross section, enable downsizing and suit for use in restricted mounting spaces. Pre-Lubricated. Good running properties.
3 Review
Dimensions: 20x42x12 mm. Rubber seal on both sides. 100% Chrome Steel for higher resistance and durability. Supports 21,000 rpm. Our high-quality bearing is made to reduce your replacement frequency and maintenance cost.
3 Review
Setscrew shaft collar for applications supporting low axial loads and simple positioning. Effective on shafts made of softer material than the setscrew material. Steel for weldability and rust resistance with a black oxide finish for a decorative appearance and for resistance to stick-slip, white corrosion, and abrasion. Includes a socket setscrew for…
Read more about this product
3 Review
✔ 100% - Dimensional tolerance inspection for optimum assembly. ✔ Material - Manufactured by chrome steel sturdy and durable. ✔ Seal - Preserve grease and prevent impurities from entering. ✔ Guarantee - 6 Months free replacement or refund no reason. ✔ Expert - Professional bearing manufacturing began in 1945.
3 Review
Quality Engineered Precision Product. Dynamic Load Rating 6 kN. Static Load Rating 3.3 kN. Grease Reference Speed 19000 rpm. Oil Reference Speed 28000 rpm.
3 Review
Suit for Shaft diameter 1" and hubs wheels diameter 2". 100% Dimensional Tolerance Detection to Ensure Optimum Install Suitability. Our high-quality bearing is made to reduce your replacement frequency and maintenance cost. Ball bearing has the advantages of low noise, fast heat dissipation, low friction, high speed and high temperature resistance. Fit…
Read more about this product
3 Review
3mm in diameter; Package includes 50 piece ball. Precision grade G100 balls. Made of 316L stainless steel with higher corrosion resistance than the type of 316. smooth surface precision balls. Offer excellent resistance to sulphuric acid compounds.
3 Review
R4-2RS (I.D.=1/4", O.D.=5/8", Thickness=0.196"). r4-2z bearings are sealed on BOTH SIDES to keep lubricant in. Chromium Steel long-life bearings, smooth and low noise. ABEC Tolerance 1 (P0), Z2 Noise Level for most general use. Static load rating of 615 newtons and dynamic load rating of 1480 newtons.
3 Review
For use with Lovejoy L type Jaw style flexible coupling assembly (sold separately). Iron sintered with powdered metals for strength, durability, and corrosion resistance. Transfers shock and misalignment to the center element of the coupling assembly for reduced wear on the shaft assembly. Country of origin: United States.
3 Review
Made of high quality 45# steel ,high wear-resistance,longtime use. Lower contact ratio between gears, higher load capacity. It only can fit for 2module gear,20 teeth,90 degrees,Hole Dia 14mm. Suitable for used in agricultural equipment, textile machinery, printing machinery, Mechanical transmission, etc. Note:1 to 1 bevel gear (only 1 to 1 match, can…
Read more about this product
3 Review
Model: 6200-2RS ball bearings, Inner Dia.=10mm, Outer Dia.=30mm, Thickness=9mm. This metal bearing seals on both sides keeping lubricant in and contaminants out. 6200-2RS roller bearings are one of the most widely used rolling bearings. They are used to accommodate radial and axial loads in both directions. Chromium Steel made with heat treating…
Read more about this product
3 Review
Size: FKG deep groove ball bearings have an inside diameter of 15 mm, an outside diameter of 35 mm and a width of 11 mm. Rubber seal: These deep groove ball bearings have double-sided rubber seal to prevent the ingress of impurities and to save lubricant. Performance: FKG ball bearing have the advantages of low noise, fast heat dissipation, low friction…
Read more about this product
3 Review
Model: SCS8UU (Bearing No.: LMF8UU, Nominal Shaft Diamter (dr): 8mm). Aluminium Alloy Linear Ball Bearing Slide Block Units. Light-weight housing and Chromium Steel bearing ball, good abrasion resistance, high precision and good strength. Smooth moving, low friction, high rigidity and long working life. Suitalbe for kinds of electronic equipment/guide…
Read more about this product
3 Review
Size: 624ZZ (Inner Dia.=4mm, Outer Dia.=13mm, Thickness=5mm). Shields on BOTH SIDES of the bearing to keep dust out. Suitable for high speed operation. Made from Carbon Steel, durability and resistance to under heavy loads. ABEC Tolerance 1 (P0) for most general use. Same As 624-2Z / 80024. Pre-Lubricated, Easy to maintain.
3 Review
Dimensions: 25x47x12. Rubber seal on both sides. 100% Chrome Steel for higher resistance and durability. Supports 15,000 rpm. Our high-quality bearing is made to reduce your replacement frequency and maintenance cost.
3 Review
The material is carbon steel, which is very suitable for linear motion rod. The surface has been chrome plated to enhance the hardness. Chamfer on both ends, easier to install linear bearings and won't hurt fingers when installing it. Diameter 10mm, tolerance -0.005mm to -0.03mm ( 9.995mm - 9.97mm). Length 300mm, tolerance ± 0.5mm ( 299.5mm - 300.5mm ).
3 Review
A must have for print quality and printer feel/function: It fixed a lot of bed leveling, 1st layer adhesion issue, prevent the one side bed sagging, is known to improve print quality as well as prevent issues with dual z axis rods going out of sync. Compare with brass nuts, These nuts have a lot tighter fit than any brass nuts in the past and are dead…
Read more about this product
3 Review
✔ 100% - Dimensional tolerance inspection for optimum assembly. ✔ Material - Manufactured by chrome steel sturdy and durable. ✔ Seal - Preserve grease and prevent impurities from entering. ✔ Guarantee - 6 Months free replacement or refund no reason. ✔ Expert - Professional bearing manufacturing began in 1945.
3 Review
*Cr - Dynamic Load Rating 13.6 kN. C0r - Static Load Rating 6.6 kN. Grease Reference Speed 15000 rpm. Oil Reference Speed 22000 rpm. 2Pcs.