Review on 📺 Mount-It! Premium Swivel Caddy Corner TV Mount - Full Motion Wall Bracket for 37-63 inch Flat Panel Screens - VESA up to 800x400, 132 lb Capacity, Black by Andrew Frison

I have Mount-It! MI-484C Swivel TV Corner Mount Premium swivel wall mount for 37-63" LCD OLED Plasma 4K Flat Panels with VESA screens up to 800 x 400, 132lb capacity, black to fit our Sony 2017 65" -TV year, £50 to mount in the corner of our room. This works well with about 6 inches of space on each side of the TV when both bracket arms are almost fully extended, allowing for side to side movement and left/right tilt. - With a standard wall mount I assume there is only an inch of clearance. A pair of screws left and right of the center pivot were then tightened as the mount was leveled with a built-in spirit level to slow any left/right rotation. After the TV was mounted and centered on the bracket, very little adjustment was required using the outer plane on top of the TV. Everything seems to be securely fastened. I found the instructions that came with the mount to be sufficient, but difficult for my old eyes to read due to the tiny writing used in some places. Our Setup: Not sure if there would be enough room for a 65 inch TV, we decided to install some 10x2's on the walls that were bolted down. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. After the TV was mounted and centered on the bracket, very little adjustment was required using the outer plane on top of the TV. Everything seems to be securely fastened. I found the instructions that came with the mount to be sufficient, but difficult for my old eyes to read due to the tiny writing used in some places. Our Setup: Not sure if there would be enough room for a 65 inch TV, we decided to install some 10x2's on the walls that were bolted down. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. After the TV was mounted and centered on the bracket, very little adjustment was required using the outer plane on top of the TV. Everything seems to be securely fastened. I found the instructions that came with the mount to be sufficient, but difficult for my old eyes to read due to the tiny writing used in some places. Our Setup: Not sure if there would be enough room for a 65 inch TV, we decided to install some 10x2's on the walls that were bolted down. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. but for my old eyes it's hard to read because of the tiny font used in some places. Our setup: Since we weren't sure if there would be enough room for a 65 inch tv we decided to install some 10x2's on the walls which were bolted down. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. but for my old eyes it's hard to read because of the tiny font used in some places. Our setup: Not sure if there would be enough space for a 65 inch TV, we decided to install some 10x2's on the walls that were bolted to stands. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. but for my old eyes it's hard to read because of the tiny font used in some places. Our setup: Not sure if there would be enough space for a 65 inch TV, we decided to install some 10x2's on the walls that were bolted to stands. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. but for my old eyes it's hard to read because of the tiny font used in some places. Our setup: Not sure if there would be enough space for a 65 inch TV, we decided to install some 10x2's on the walls that were bolted to stands. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. to install some 10x2's on the walls that were bolted with studs. The bracket was then mounted to this 10x2 using the 6 screws/washers provided. to install some 10x2's on the walls that were bolted with studs. The bracket was then mounted to this 10x2 using the 6 screws/washers provided.