Review on 📐 A4 Paper Trimmer: Precise Cut with Blade Gridded Photo Guillotine Craft Machine, 12 inch Length, A4-B7 Use by Amber Perez

Hard plastic feet instead of soft rubber so it slides all over the table. The blade is not a blade but a square curved lever with an angled edge. quite sharp and finishes on the board with an identical built in sharpening angle for cutting like a large pair of scissors. The alignment ruler is very flimsy and is not attached to the board or locked in place in any way. The paper clip attached to the cutter arm should reach every 18 inches, but it only cuts 11 inches of paper. The GRIP is not attached and you SHOULD NOT squeeze it fully into your hand as the hand will then go no further than 16, 5 inches and will not snap onto the pin. Gently tap the handle about 0.5 inches to fully close and lock into place. I've only cut a few test sheets and it worked, but I'm not very happy with the design or the finish. Another design Amazon has to steal and tweak to improve and sell for less. Update: I used it to cut out some small booklets and the "blade" (not a blade actually) was already dull and messed up the last booklet I tried to cut. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. updated: I used it to cut out some small booklets and the "blade" (not really a blade) was already dull and messed up the last booklet I tried to cut. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. Update: I used it to cut out some small booklets and the "blade" (not a blade actually) was already dull and messed up the last booklet I tried to cut. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. (not actually a blade) was already dull and messed up the last hilt I tried to cut. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. Update: I used it to cut out some small booklets and the "blade" (not a blade actually) was already dull and messed up the last booklet I tried to cut. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. (not actually a blade) was already dull and messed up the last hilt I tried to cut. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. Update: I used it to cut out some small booklets and the "blade" (not a blade actually) was already dull and messed up the last booklet I tried to cut. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. Update: I used it to cut out some small booklets and the "blade" (not a blade actually) was already dull and messed up the last booklet I tried to cut. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. Update: I used it to cut out some small booklets and the "blade" (not a blade actually) was already dull and messed up the last booklet I tried to cut. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money. It was only 10 sheets thick and is supposed to cut cleanly through 12 sheets. I did a test and it barely cuts through a sheet without fraying the edges. waste of money.