1/2" 55Ft XHF 3:1 Waterproof Adhesive Lined Heat Shrink Tubing Roll Marine Grade Insulation Sealing Oil-Proof Wear-Resistant Black Review

My True treadmill front roller is small diameter (1.75") and had a plastic sleeve on it to increase friction for advancing the belt. In time, this sleeve split and bunched up causing an annoying sound when using the treadmill. The fix for this is to remove the remnant plastic sleeve, clean the roller and cover it with a piece of shrink tube. The 2" variety of XHF tube was selected and delivered in one day by Best Buy. A heat gun was sufficient to shrink the tube onto the treadmill roller…

Loosely coiled in a 1 gallon Ziploc bag. Shrink tube is not glued together in a tight unusable coil like others I have ordered. I will buy this again.

Can confirm 5/8" works for ethernet cable labels. Just about slips over & then it really does have 3:1 ratio. Goes to pretty much exactly 5mm. Used heat gun. Gets all smoky & brown if you use a flame. Pretty thick when done though. About 1/16" thick extra around the cable. I left some over the cable relief part and so I get some extra cable relief from the deal

The product was just what I wanted. I used it to cover 5/8 chain for a climbing tree stand. Rugged and durable. It was hard to get the chain they but that was due to the sizes being very close before shrinking .

Seems like a very good quality shrink. Thicker than most others I have used. Shrank well and glue squeezed out. Time will tell.

Needs a lot of heat to get it to fully sink down to size and to shrink evenly. But once it is down to its shrunken size, the material is very think. So it should be pretty durable.

This has something akin to hot glue coating the inside, so when it's heated enough to shrink, that coats everything and seals it completely. It says it shrinks 3:1 and I'd say that's about right without measuring, and it's thicker when shrunk than I expected. Since it went on an outdoor cord, the thickness and good seal are both desirable. Won't know how well it holds up until it's been outside a while, but the initial results are certainly promising.

Wanted a material that was non slip to use in the bottom of my canoe. When heated it shrunk evenly and smoothly. This allows me to stand up when landing that big bass.

By far the best heat shrink I've ever used for automotive applications. It shrinks down and seals on a small 18ga wire and can fit around a larger 10 gauge with no problem. Fits well with red, blue, and yellow crimp connectors. As the description reads, definitely keeping a stock of this stuff in my shop!

Use to cover the ear clamps on a garden hose repair. Fits over the female hose ends and shrinks down nicely. May not provide adequate protection against water ingress.

The tube has glue inside so it sits great on the cables. It shrinks very even and is all over a good quality shrink tube. Specially for this price.

Needed some kind of solution to repair the handle of a fishing rod I'd been meaning to fix. Did the trick with this heat shrink tubing. Great product.

Very good product. I have it in two sizes and between the two, they cover most needs. It seals very quickly and evenly. It is a good feature that it comes in a roll so you can cut the length needed. Very good heat shrink.

I used this to cover a sticky hand held apparatus. But it shrunk enough for what I needed.. I Florida some rubberlike coated parts become very sticky!

I bought this large shrink wrap to bridge the connection between a 20 amp to 30 amp converter that's not rated for outdoors. I cut it so that it was a bit longer than necessary hoping that it would shrink down small enough to get the melted glue onto the shank of the connecting cord for a better water proof seal. It did so wonderfully. While it's only been a month or so, I've had no problems with my marina electrical connection so far, and don't expect to. It took a little while with the heat…